JONATHAN Y JYL7587A Henry LED Pendant Lamp Instruction Manual

JONATHAN Y JYL7587A Henry LED Pendant Lamp

Product Information

This lighting fixture is designed to provide illumination in indoor spaces. The model number of this product is JYL7587A, and its dimensions are 17.875 inches in diameter and adjustable in height from 33 to 92 inches. The package includes the following parts:

• Mounting bar (A) – 1 piece
• Lock link (I) – 1 piece
• Ground screw (B) – 1 piece
• Outlet box screw (C) – 1 piece
• Fixture body (J) – 2 pieces
• Wire nut (D) – 3 pieces
• Canopy nut (E) – 2 pieces
• Canopy unit (F) – 1 piece
• Chain (G) – 1 piece
• Rod (H) – 1 piece
• Light bulb (K) – 1 piece (4-watt LED bulb included in the box)

Product Usage Instructions

1. Before starting the assembly, ensure that all parts are present. Compare the parts with the package contents list and hardware contents list. If any part is missing or damaged, do not proceed with the assembly.
2. Estimated assembly time is approximately 20 minutes.
3. Attach the mounting bar (A) to the junction box using the outlet box screw (C).
4. Connect the fixture body (J) and rod (H) together using the lock link (I). Attach the metal chain (G) to the canopy unit (F) on the top and attach it to the rod (H) on the bottom.
5. Connect the wires as follows:
   • Connect the Hot, Black, or Red Outlet Supply Wire to the Black wire of the parallel cord (round & smooth).
   • Connect the Neutral, White Outlet Supply Wire to the White wire of the parallel cord (square & ridged).
   • Connect any Clear, Brown, Gold, or Black wire without Tracer (colored stripes) to the Insulated Wire (not green) with copper metal conductor.
   • Connect any Clear, Brown, Gold, or Black wire with Tracer (colored stripes) to the Insulated Wire (not green) with Silver metal conductor.

Note: When using parallel wire (SPT I & SPT II), the neutral wire is square shaped and ridged, while the hot wire will be round in shape and smooth.

1. For installation in the United States:
   • Wrap the ground wire from the outlet box around the green ground screw (B) on the mounting bracket, at least 2 inches from the wire end. Tighten the ground screw.
   • If the fixture is supplied with a ground wire, connect it to the outlet ground wire using a wire connector.
2. For installation in Canada:
   • If the fixture is supplied with a ground wire, wrap it around the green grounding screw on the mounting bracket. Tighten the ground screw.
3. Raise the canopy unit (F) and thread it onto the outlet box screws. Secure it with the canopy nut (E).
4. Install the provided light bulb (K) into the socket.
5. Use a Type A bulb with a maximum wattage of 60 watts, or a CFLbulb with a maximum wattage of 13 watts, or an LED bulb with a= maximum wattage of 9 watts.

Enjoy your lamp!

Model#: JYL7587A
Product Dimensions: 17.875″D x 33″-92″H

WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.

CARE AND MAINTENANCE

• To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
• To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
• Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.

NOTICE& IMPORTANT SAFETY INSTRUCTIONS

• Please make sure that you have all parts indicated before you begin assembly of this item
• This item should be assembled on a soft surface to prevent scratching the finish during assembly
• To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
• The external flexible cable or cord of this lamp cannot be replaced

If the cord is damaged, the lamp shall be destroyed

Part List and Hardware List

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 20 minutes.

1. Attach the mounting bar (A) to the junction box with outlet box screw (C).
2. Connect the fixture body (J) and rod (H) together with lock link (I), attach the metal chain (G) to the canopy unit (F) on the top and attach it to the rod (H) on the bottom.
3. Connect wires.
   Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
   ---|---
   Black| White

• Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)

Clear, Brown, Gold or Black without Tracer     (colored stripes)

|

Clear, Brown, Gold or Black with Tracer (colored stripes)

Insulated Wire (not green) with copper metal conductor

|

Insulated Wire (not green) with Silver metal conductor.

Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions:

  * For installation in the United States: Wrap ground wire from outlet box around green ground screw(B) on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
  * For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.

4. Raise the canopy unit (F) thread to the outlet box screws, secure with canopy nut (E).
5. Install the light bulb (K) to the socket.

PLEASE USE TYPE”A” BULB MAX 60-WATT OR CFL BULB MAX 13-WATT OR LED BULB MAX 9-WATT, THERE IS 1PC LED 4-WATT BULB IN THE BOX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>