3nstar PTE0905 15 All-In-One POS System User Manual

June 5, 2024
3nStar

3nstar PTE0905 15 All-In-One POS System logo

3nstar PTE0905 15 All-In-One POS System

3nstar PTE0905 15 All-In-One POS System productSafety and Warranty

  1. Read these safety instructions carefully.
  2. Disconnect from power outlet before cleaning, disassembly or transport. Do not use liquid or spray detergents for cleaning. Use a damp cloth only and avoid any prolonged contact with moisture.
  3. Keep the unit away from humidity.
  4. Place the unit on a sturdy surface before servicing or operation to prevent accidental drops.
  5. The openings on the enclosure are for ventilation. Do NOT cover the openings.
  6. Make sure the voltage and load ratings of the power source are correct before connecting the equipment to the power outlet.
  7. Position the power cord to prevent accidental tripping. Do not twist, pinch or clip the power cord.
  8. All cautions and warnings printed on the equipment should be followed.
  9. If the equipment is not used for a long time, disconnect it from the power source.
  10. Never pour any liquid into openings. This could cause fire or electrical shock.
  11. For safety reasons, only qualified service personnel should open and service the equipment.
  12. If any of the following situations arises, get the equipment checked by service personnel:
    • The power cord, plug, or adapter is visibly damaged.
    • Liquid has entered into the equipment.
    • The equipment has been exposed to moisture.
    • The equipment has been dropped and damaged.
    • The equipment has obvious signs of breakage.
  13. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4°F) OR ABOVE 60° C (140° F).

Introduction

Main Features

  • Platform: INTEL Coffee Lake platform support INTEL gen 9 processor

  • Panel PC with Dual hinge stand: Adjustable angle and height
    Improve the viewing angle, enhance the user experience, can also be Desktop, Pole or Wall-mounted.

  • Shared Peripherals: Share the same peripherals with XPOS

15” PTE0905

3nstar PTE0905 15 All-In-One POS System fig 1 3nstar PTE0905 15 All-In-One POS System fig 2

Optional Peripheral PTE0905

3nstar PTE0905 15 All-In-One POS System fig
33nstar PTE0905 15 All-In-One POS System fig
5

  • The thickness of wall mount bracket (no space for power adapter)= 21mm
  • The thickness of Wall Mount bracket (space for power adapter= 57mm

Cable Management (PTEO905)

3nstar PTE0905 15 All-In-One POS System fig 6

Adjustable Angle (PTE0905) 

3nstar PTE0905 15 All-In-One POS System fig
7

Dimension (PTEO905)

3nstar PTE0905 15 All-In-One POS System fig
8

Rear /O Panel Connectivity (PTE0905)

IO Default3nstar PTE0905 15 All-In-One POS System fig
9

I/O Port Connector Type Application
Video Ports HDMI x1 For 2nd HDMI Monitor
PUSB 24V 24V Power USB
Smart I/O Including 5V/12V/24V (BIOS select) and USB 2.0 x 2 and Com port x
1 I/O cables
20V in 20V DC in (130W)
Cash drawer 12V / 24V adjust by bios
USB DP or Smart DD USB TC x1 (USB DP, SMART DD by BIOS select) For 2nd USB

DP Monitor
Serial port| RJ45 Com port x 3|
USB| USB 2.0 x 2, USB 3.0 x 2|
Ethernet| Giga Lan|

Packing List (PTEO905)

Standard Optional & Peripherals
1 15”
2 20V 130W Power Adaptor
3 AC Cord Cable
4 RJ-45 to D-sub9 Convert Cable x1

Hardware Installation & Setting

Optional Device Installation

  1. Customer Display Installation,
    Install Pull up the connector 3nstar PTE0905 15 All-In-One POS System
fig 10

  2. Install 2nd display (integrated type) PTE0905-M10 on Smart DP Remover Plastic Cover 3nstar PTE0905 15 All-In-One POS System fig 12

  3. Remove & Install Cable Cover
    Remove Cable Cover3nstar PTE0905 15 All-In-One POS System fig
13

Device status setting

Driver& Utility Installation and Setup

  1. Chipset
    • Locate chipset folder and double click on [ SetupChipset] 3nstar PTE0905 15 All-In-One POS System fig 14
    • Click [ Next ]
    • Click [ Accept ]3nstar PTE0905 15 All-In-One POS System fig 15
    • Click [ Install ]
    • Click [ Yes ]3nstar PTE0905 15 All-In-One POS System fig 16
    • Click [ Restart Now ]3nstar PTE0905 15 All-In-One POS System fig 17
  2. Audio
    • Double click [ Setup ]
    • Click [ Yes ]3nstar PTE0905 15 All-In-One POS System fig 18
    • Click [ Next ]
    • Click [ Yes, I want to restart my computer now ], [ Finish ] 3nstar PTE0905 15 All-In-One POS System fig 19
  3. Graphics
  4. Double Click [ igxpin ]
  5. Click [ Yes ]3nstar PTE0905 15 All-In-One POS System fig 20
  6. Click [ Next ]
  7. Click [ Next ]3nstar PTE0905 15 All-In-One POS System fig 21
  8. Click [ Finish ]3nstar PTE0905 15 All-In-One POS System fig 22
  9. Intel® ME
    • Double Click [ SetupME ]
    • Click [ Next ]3nstar PTE0905 15 All-In-One POS System fig 23
    • Accept Terms then click [ Next ]
    • Click [ Next ]3nstar PTE0905 15 All-In-One POS System fig 24
    • Click [ Yes ]
    • Click [ Finish ]3nstar PTE0905 15 All-In-One POS System fig 25
  10. Serial IO
    • Double Click [ SetupSerialIO ]
    • Click [ Next ]3nstar PTE0905 15 All-In-One POS System fig 26
    • Accept terms then click [ Next ]
    • Click [ Next ]3nstar PTE0905 15 All-In-One POS System fig 27
    • Click [ Next ]
    • Select Yes, I want to restart this computer now the click [ Finish ]3nstar PTE0905 15 All-In-One POS System fig 28
  11. Sensor
    • Double Click [ install ]
    • Click [ Yes ]3nstar PTE0905 15 All-In-One POS System fig 29
  12. OPOS
    Please contact customer service to request  “ OPOS Driver for 3nStar CashDrawer & VFD/LCM”  **
    **

Specification

15”

Model| PTE0905
CPU| I5-9500TE (Embedded)(9 Gen)
Resolution| 1024 * 768    400nits
Touch| Projected Capacitive (Multi-touch)
DRAM| DDR4 SO-Dimm Slot x 2 (Support 2666 MHz & max 64G)
M.2

storage

| M.2 2280 slot x 1 (Interface SATA 3 & Support PCIE), optional for 2nd M.2
Default I/O| Video Ports : HDMI x1 PUSB 24V : 24V Power USB

SMART I/O : Including 5V/12V/24V (BIOS select) and USB 2.0 x 2 and Com port x 1 20V in: 20V DC in ( 130W )

Cash drawer: 12V / 24V adjust by bios

USB DP or SMART DD : USB TC x1 (USB DP, SMART DD by BIOS select )

Serial port :RJ45 Com port x 3 USB: USB 2.0 x 2 , USB 3.0 x 2

Ethernet :Giga Lan

|
Optional: SMART I/O

Cables

| | | | | | | |
---|---|---|---|---|---|---|---|---
| Cable Type| Application| Side A| Side B| P/N|
1| 12V Y

cable

| 2nd Monitor| TC connector| 12V DC jack & USB B| RA9000XC4441|
2| 24V

Printer Y cable

| Printer| TC connector| 3 pin hoshiden & USB B| RA9000XC4390|
3| COM

cable

| Com port device| TC connector| DB 9| RA9000XC4391|
4| USB

cable

| Payment device power| TC connector| 12V DC jack| RA9000XC4442|
| | | | | |
|
Speakers| 2 x 2W
OS| Windows 10 LTSC
Power| 20V 130W

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals