JONATHAN Y JYL1401A Koda 13 Inch Pendants Instruction Manual

JONATHAN Y JYL1401A Koda 13 Inch Pendants

Assembly Instruction

CAUTION: Read instructions carefully and turn the electricity off at the main circuit breaker panel before beginning installation.

• ITEM#:JYL1401A
• Product Dimensions: 13″Lx 13″W x 18″-198″ H
• Note: 2 Assembly Options

Option 1: Portable lamp with plug.

Option 2: Hard wired.

Care and Cleaning

• To clean the outside of the fixture, use a dry or slightly dampened clean cloth(use clean water, never a solvent) to wipe the surface of the fixture.
• To clear the inside of the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth(use clean water, never a solvent) to wipe the interior surface of the fixture
• Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use Only a dry soft cloth to dust or wipe carefully.

Option 1: Assembly instruction(portable)

Part List

• PLEASE LOCATE ALL ITEMS BEFORE THROWING AWAY THE BOX
• Estimated Assembly Time:30 minutes

1. Drill two holes with a depth of 1-1/8″ into the firm ceiling at the desired location for the lamp (D), Install two anchors (A) into the holes.

2. Insert the screw(B) through J-hook (C1) into the anchor (A)and tap gently with a hammer to set anchors firmly in place.
   Then install J-hook(C2).

3. Adjust the desired location on the cord of lamp (F), Wrap the wire around the J-hook(C) twice.
   Note: Do not twist the cord.

4. Insert the screw(B) through hook (D1) into the anchor (A)and tap gently with a hammer to set the anchors firmly in place.

5. Put the wire into the hook(D1), then install hook(D2).
   Note: Do not twist the cord.

6. Put the shade(F) into the Socket(E), then screw the socket ring(G) into the socket.

7. Install bulb(H). Be sure to use a light bulb(H) with a wattage no greater than specified on this fixture.
   Always make sure that the electrical current is turned off before changing bulbs.

8. Use the inline switch-on cord to turn the light on/off.

9. Do not install on a radiant-heating ceiling.

PLEASE USE ON/OFF TYPE”A” BULB MAX 100-WATT OR LED BULB MAX 12 -WATT THERE IS AN LED 4-WATT BULB IN THE BOX

Option 2: Assembly instruction(Hard wired)

Part List and Hardware List

Installation

• Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
• Estimated Assembly Time: 30 minutes.

1. Carefully cut the pre-attached plug, cord, and switch to your desired length as shown, and discard the part plug and switch.

2. Insert the end of the cord into the corresponding hole of the canopy ( E ), and mounting plate ( B ) as shown. Thread cord into bracket ( M ) as shown.
   Note: Cutting the cord so that they are at least 6 inches (152.4mm) long within an outlet box and extend max. 3.1m long measured from the point where the cord emerges from the body of the lamp.

3. Fix the mounting bracket(B) to the outlet box with machine screw(C).

4. Make wire connections, with wire connectors(A), following the reference chart listed below.
   Connect, Hot, Black, or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
   ---|---
   Black (Hot)| White (Neutral)

• Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
  Clear, Brown, Gold, or Black without Tracer (colored stripes)|

Clear, Brown, Gold, or Black with Tracer (colored stripes)

Insulated Wire (not green) with a copper metal conductor

|

Insulated Wire (not green) with Silver metal conductor.

*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions:
a) For installation in the United States: Wrap ground wire from the outlet box around green ground screw(E) on the mounting bracket, no less than 2″ from the wire end. Tighten ground screw(E). If the fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire connector.
b) For installation in Canada: If the fixture is supplied with ground wire, wrap ground wire around the green grounding screw(E) on the mounting bracket. Tighten ground screw(E).

5. Orient the ceiling canopy(F) so that the mounting screws(D) protruding from the mounting bracket go into the holes in the canopy, then secure it with the provided screwed balls(G).
6. Put the set screw(G) by the Wrench(H) to tighten.
7. Put the shade(J) onto Socket(I), then screw the socket ring(K) into the socket.
8. Install bulb(L). Be sure to use a light bulb(L) with a wattage no greater than specified on this fixture. Always make sure that the electrical current is turned off before changing bulbs.

PLEASE USE ON/OFF TYPE”A” BULB MAX 100-WATT OR LED BULB MAX 12 -WATT THERE IS AN LED 4-WATT BULB IN THE BOX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>