JONATHAN Y JYL1405A Isla 14 Wide LED Pendant Instruction Manual
- October 30, 2023
- JONATHAN Y
Table of Contents
JONATHAN Y JYL1405A Isla 14 Wide LED Pendant
Product Information
The JYL1405A product is a lamp that comes in two assembly options: portable
with plug or hardwired. The dimensions of the lamp are 14Lx 14W x 12-192H. The
portable option requires assembly with a part list including anchor, screw,
J-hook, socket, shade,
socket ring, hook, and bulb. The hardwired option requires assembly with a
part list including wire connector, mounting bracket, mounting screws, ground
screw, canopy, screwed balls, screw nut, socket, shade, and bulb. The lamp can
use an on/off type A bulb max60-watt or LED bulb max 9-watt. There is an LED
4-watt bulb included in the box.
Product Usage Instructions
Before beginning installation, read the instruction carefullyand turn off electricity at the main circuit breaker panel. If any part is missing or damaged, do not attempt to assemble the product.
Portable Lamp with Plug Assembly Instructions
Estimated assembly time: 30 minutes
- Drill two holes with depth 1-1/8 into the firm ceiling at the desired location for the lamp (D),Install two anchor (A) into the holes.
- Insert the screw(B) through J-hook (C1) into the anchor (A)and tap gently with a hammer to set anchors firmly in place. Theninstall J-hook(C2).
- Adjust the desired location on the cord of lamp (F), Wrap the wire around the J-hook(C) twice. Note: Do not twist the cord.
- Insert the screw(B) through hook (D1) into the anchor (A)and tap gently with a hammer to set anchors firmly in place.
- Put the wire into the hook(D1), then install hook(D2). Note: Do not twist the cord.
- Put the shade(F) on to the Socket(E), then screw the socket ring(G) into the socket.
- Install bulb(H). Be sure to use light bulb(H) with wattage no greater than specified on this fixture. Always make sure thatelectrical current is turned off before changing bulbs.
- Use the inline switch on cord to turn light on/off.
- Do not install on a radiant-heating ceiling.
Hardwired Assembly Instructions
Estimated assembly time: 30 minutes
-
Carefully cut pre-attached plug, cord and switch to yourdesired length as shown and discard the part plug and switch.
-
Insert end of cord into corresponding hole of canopy (E), and mounting plate (B) as shown. Thread cord into bracket (M) as shown.
Note: Cut the cord so that they are at least 6 inches (152.4mm) long within an outlet box and extend max. 3.1m long measured from the point where the cord emerges from the body of the lamp. -
Fix the mounting bracket(B) to the outlet box with machine screw(C).
-
Make wire connections, with wire connectors(A), following the reference chart listed below:
- Connect Hot, Black or Red Outlet Supply Wire to: Black (Hot) Parallel Cord (round & smooth) Clear, Brown, Gold or Blackwithout Tracer (colored stripes)
- Connect Neutral, White Outlet Supply Wire to: White (Neutral)
-
Attach the canopy (E) to the mounting bracket (B) with screwed balls (F) and screw nut (G).
-
Put the shade (J) on to the socket (I), then screw the socketring (K) into the socket.
-
Install bulb (L). Be sure to use light bulb (L) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
-
Use the switch on the wall to turn light on/off.
-
Do not install on a radiant-heating ceiling.
Assembly Instruction
CAUTION: Read instruction carefully and turn electricity off at main
circuit breaker panel before beginning installation.
ITEM#: JYL1405A
Product Dimensions: 14″Lx 14″W x 12″-192″H
Note: 2 Assembly Options
- Option 1: Portable lamp with plug
- Option 2: Hard wired
Care and Cleaning
- To clean the outside of the fixture, use a dry or slightly dampened clean cloth(use clean water, never a solvent) to wipe the surface of the fixture.
- To clear the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth(use clean water, never a solvent) to wipe the interior surface of the fixture
- Do not use any cleaners with chemical, solvents or harsh abrasives. Use Only a dry soft cloth to dust or wipe carefully.
Option 1: Assembly instruction(portable)
Part List
PLEASE LOCATE ALL ITEMS BEFORE THROWING AWAY THE BOX
Estimated Assembly Time:30 minutes
-
Drill two holes with depth 1-1/8″ into the firm ceiling at the desired location for the lamp (D),Install two anchor (A) into the holes.
-
Insert the screw(B) through J-hook (C1) into the anchor (A)and tap gently with a hammer to set anchors firmly in place.
Then install J-hook(C2). -
Adjust the desired location on the cord of lamp (F), Wrap the wire around the J-hook(C) twice.
Note: Do not twist the cord. -
Insert the screw(B) through hook (D1) into the anchor (A)and tap gently with a hammer to set anchors firmly in place.
-
Put the wire into the hook(D1), then install hook(D2).
Note: Do not twist the cord. -
Put the shade(F) on to the Socket(E), then screw the socket ring(G) into the socket.
-
Install bulb(H). Be sure to use light bulb(H) with wattage no greater than specified on this fixture.
Always make sure that electrical current is turned off before changing bulbs. -
Use the inline switch on cord to turn light on/off.
-
Do not install on a radiant-heating ceiling.
PLEASE USE ON/OFF TYPE”A” BULB MAX 60-WATT OR LED BULB MAX9 -WATT THERE IS LED 4-WATT BULB IN THE BOX
Option 2: Assembly instruction(Hard wired)
Part List and Hardware List
Installation
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 30 minutes.
-
Carefully cut pre -attached plug ,cord and switch to your desired length as shown and discard the part plug and switch .
-
Insert end of cord into corresponding hole of canopy ( E ),and mounting plate ( B ) as shown. Thread cord into bracket ( M ) as shown.
Note: Cuting the cord so that they are at least 6 inches (152.4mm) long within an outlet box and extend max. 3.1m long measured from the point where the cord emerges from the body of the lamp. -
Fix the mounting bracket(B) to the outlet box with machine screw(C).
-
Make wire connections, with wire connectors(A), following the reference chart listed below.
Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
---|---
Black (Hot)| White (Neutral)
- Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)|
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
|
Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. ) Grounding Instructions:
* **a)** For installation in the United States: Wrap ground wire from outlet box around green ground screw(E) on mounting bracket, no less than 2″ from wire end. Tighten ground screw(E). If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
* **b)** For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw(E) on mounting bracket. Tighten ground screw(E).- Orient the ceiling canopy(F) so that the mounting screws(D) protruding from the mounting bracket go into the holes in the canopy,then secure it with the provided screwed balls(G).
- Put the set screw(G) by the Wrench(H) to tighten.
- Put the shade(J) on to the Socket(I), then screw the socket ring(K) into the socket.
- Install bulb(L). Be sure to use light bulb(L) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
PLEASE USE ON/OFF TYPE”A” BULB MAX 60-WATT OR LED BULB MAX 9 -WATT THERE IS LED 4-WATT BULB IN THE BOX
ENJOY YOUR LAMP
Documents / Resources
|
JONATHAN Y JYL1405A Isla 14 Wide LED
Pendant
[pdf] Instruction Manual
JYL1405A Isla 14 Wide LED Pendant, JYL1405A, Isla 14 Wide LED Pendant, 14 Wide
LED Pendant, LED Pendant, Pendant
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>