JONATHAN Y JYL3080A Sylva 72.5 Inch Floor Lamp Instruction Manual
- October 30, 2023
- JONATHAN Y
Table of Contents
JONATHAN Y JYL3080A Sylva 72.5 Inch Floor Lamp
Product Information
The JYL3080A is a floor lamp that comes with three shades and three bulbs. The lamp base, lamp body, and socket are made of materials appropriate to the product’s design and functionality. The product dimensions are 34Lx 34W x 72.5H. Users should carefully inspect the product for any damage or defects before attempting installation. If there is any damage or defect, do not install the product as it cannot be returned once it has been installed. The product manual also recommends the use of on/off type A bulbs with a maximum wattage of 40 watts or LED bulbs with a maximum wattage of 9 watts.
Product Usage Instructions
- Before assembly, ensure that all parts are present and undamaged. Compare the parts with the package contents list and hardware contents list provided in the manual. If any part is missing or damaged, do not attempt to assemble the product.
- To assemble, pull the power cord to connect the Lamp body (B) to the Base (A). Put the shade (D) on the socket (C), then screw the Lamp body (B3) onto the Lamp body (B2) and tighten the Socket ring (E). Screw the Lamp body (B2) onto the Lamp body (B1), insert the bulb (F) into the socket (C), and screw the Lamp body (B1) onto the Lamp base (A). Be careful not to twist the power cord and tighten it securely.
- Put the light on a level surface to check if everything is stable.
To care for and maintain the lamp, unplug the lamps before using any cleaning solutions. Dust shades with a feather duster or with an appropriate vacuum brush attachment. Wipe with a soft, dry cloth and clean lamp bases with the methods appropriate to the material. Avoid the use of chemicals and household cleaners as they may damage the finish.
- Model# JYL3080A
- Product Dimensions: 34″Lx 34″W x 72.5″H
WARNING
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE
OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN
INSTALLED.
CARE AND MAINTENANCE
Unplug lamps before using any cleaning solutions. Dust shades with a feather duster or with an appropriate vacuum-brush attachment. Wipe with a soft, dry cloth and clean lamp bases with the methods appropriate to the material. Avoid the use of chemicals and household cleaners as they may damage the finish.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
- The external flexible cable or cord of this lamp cannot be replaced; If the cord is damaged, the lamp shall be destroyed
- This portable lamp has a polarized plug (one blade is wider than the other) as a safety feature to reduce the risk of electric shock. this plug will fit in a polarized outlet only one way. if the plug does not fit fully in the outlet, reverse the plug, if it still does not fit, contact a qualified electrician. Never use with an extension cord unless the plug can be fully inserted. do not attempt to disregard this safety feature.
Part List and Hardware List
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 6 minutes.
PLEASE USE ON/OFF TYPE”A” BULB MAX 40-WATT OR LED BULB MAX 9-WATT THERE ARE 3PCS LED 4-WATT BULB IN THE BOX
Step 1
- Pull the power cord to connect the Lamp body (B) to the Base
- Screw the Lamp body (B3) onto the Lamp body (B2) Screw the Lamp body (B2) onto the Lamp body (B1)
- Screw the Lamp body (B1) onto the Lamp base (A)
- Be careful not to twist the power cord and tighten it securely
ENJOY YOUR LAMP
Step 2
- Put the shade (D) on the socket (C), then tighten the Socket ring (E) .
- Insert the bulb (F) into the socket (C).
Step 3
- Put the light on a level surface to check if everything is stable.