Clarke JETSTAR 1850 Power Washer Instruction Manual

**Clarke JETSTAR 1850 Power Washer Instruction Manual

**

INTRODUCTION

Thank you for purchasing this CLARKE Power Washer.
This pressure washer is designed for cleaning machines, vehicles, buildings, boats, facades, terraces, gardening tools, etc. by means of a high-pressure water jet (if necessary, with additional cleaning agents).

Only use accessories, replacement parts and cleaning agents recommended by Clarke international. Before attempting to use this product, please read this manual thoroughly.

LIST OF CONTENTS

The following items should be supplied in the carton. If any parts are missing or damaged, please see your Clarke dealer where you purchased the machine.

GENERAL SAFETY RULES

WARNING: WATER AT HIGH PRESSURE CAN BE DANGEROUS AND CAN CAUSE DAMAGE IF THE OPERATOR IS CARELESS. NEVER ALLOW ANYONE TO OPERATE THIS PRESSURE WASHER UNLESS THEY ARE FAMILIAR WITH THE SAFETY PRECAUTIONS.

1. NEVER direct the spray towards any person or animal.
2. NEVER direct the spray towards electrical wiring or equipment.
3. NEVER hold your finger over the high pressure nozzle.
4. NEVER allow children or untrained personnel to use this machine.
5. NEVER operate the machine with any of the covers removed.
6. NEVER attempt any repairs to this machine. Always refer to your Clarke dealer.
7. NEVER supply any liquid other than water to the water inlet.
8. NEVER use the detergent bottle to introduce flammable liquids/solvents, e.g. paint thinners, petrol, oil as there is a risk of explosion.
9. NEVER direct the jet at electrical equipment or the machine itself.
10. NEVER use the pressure washer if the supply cable or important parts of the machine are damaged.
11. ALWAYS release any residual pressure in the system by turning off the water supply and operating the trigger before disconnecting any hose or accessory.
12. ALWAYS keep the machine itself dry and well clear of water spray.
13. ALWAYS wear protective clothing and safety glasses. Loose particles and other debris may be propelled at high speed by the water jet.
14. ALWAYS grip the gun firmly and expect the spray gun to ‘kick’ when starting.
15. ALWAYS respect the requirements of the local water company. Pressure washers may only be connected to the mains drinking water supply, if a system separator (known as a backflow preventer) is installed in the supply hose.
16. ALWAYS disconnect from the water supply, and ensure the system is completely drained when not in use. Store in a cool dry location.
17. ONLY use chemical cleaning agents (detergents), that are approved for pressure washers. CLARKE Traffic Film Remover or CLARKE Wash and Wax (available from your dealer), is recommended.
18. WARNING: High pressure water jets can be dangerous if subject to misuse. The jet must not be directed at a person or anything that they are wearing.
19. WARNING: High pressure hoses, fittings and couplings are important for the safety of the machine. Use only hoses, fittings and couplings recommended by the manufacturer.
20. WARNING: Water that has flowed through a system separator (known as a backflow preventer) is considered non-drinkable.

ENVIRONMENTAL RECYCLING POLICY

 Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognized disposal facility.

SYMBOLS ON THE MACHINE

| Read the manual before use.|

| Failing to follow these instructions could result in injury or damage to the machine.
---|---|---|---

| Conforms to UKCA & CE Regulations.|

| Wear safety glasses when using this machine.

| The high pressure jet must not be directed at persons, animals, live electrical equipment or at the appliance itself

ELECTRICAL CONNECTIONS

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY.

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. Connecting it to any other power source may cause damage.

If it is necessary to change the fuse in the plug, the fuse cover must be refitted.
If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed due to damage, a replacement should be fitted, following the wiring instructions shown below. The old plug must be disposed of as insertion into a mains socket could cause an electrical hazard.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL BROWN = LIVE

If the colors of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows.

• The wire which is colored Blue must be connected to the terminal which is marked N or colored Black.
• The wire which is colored Brown must be connected to the terminal which is marked L or colored Red.
  

We strongly recommend that this machine is connected to the mains supply via a Residual Current Device (RCD) that will interrupt the supply if the leakage current to earth exceeds 30 rnA for 30 ms .

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

This symbol indicates that this is a Class II product, and does not require an earth connection.

OVERVIEW

1. Spray Gun Assembly
2. Handle
3. ON/OFF Switch
4. High Pressure Hose
5. Lance
6. Water Inlet Connection Point
7. Detergent Bottle
   

ASSEMBLY

1. Slide the brackets into their positions.

   • They will ‘click’ into place.
     

2. Connect the high pressure hose to the pressure washer as shown and tighten securely.
   

3. Insert the hose into the gun fully

4.  Slide the hose clip towards the hose to lock in place.
   

5. Insert the lance into the gun as shown and twist to lock in place.
   

CONNECTING THE MAINS WATER SUPPLY

NOTE: Always follow the regulations of your local water supplier.

1. Screw the inlet adaptor to the water inlet as shown.

2. Connect the supply hose to the inlet adaptor.

   • A standard garden hose or a reinforced hose with an inner diameter of at least 10 mm available from your CLARKE dealer will be suitable.
     

3. Connect the supply hose to the water supply.

   • The water supply must provide a minimum of 6 litres per minute at a maximum of 40°C.

4. Open the water tap fully.

OPERATION

1. Turn the water supply on, making sure that the tap is fully open.

2. Plug the mains power cable into the electricity supply.

3. Set the switch to the ON position.
   
   WARNING: FAILURE TO TURN ON THE WATER FULLY COULD CAUSE DAMAGE TO THE POWER WASHER INTERNAL COMPONENTS. WARNING: DO NOT USE THE POWER WASHER IF THE SUPPLY CABLE OR IMPORTANT PARTS OF THE MACHINE ARE DAMAGED, E.G. SAFETY DEVICES, HIGH PRESSURE HOSES, TRIGGER. WARNING: WE RECOMMEND THAT THIS MACHINE IS CONNECTED TO THE MAINS SUPPLY VIA A RESIDUAL CURRENT DEVICE.

4. Release the trigger lock.

   • The pressure washer is now ready for use.

5. Make sure that you have a firm footing and are also holding the gun and spray lance firmly.

   • Expect the spray gun to ‘kick’ when starting.

6. Pull the trigger on the gun to start water flow.

   • If you release the trigger the device will switch off again, the system remains under high pressure.
   • During longer breaks (more than 5 minutes), turn the pressure washer off. See “Shutting Down” on page 11.

7. Once the machine has been turned off, release any residual pressure in the system by turning off the water supply and operating the trigger before disconnecting any hose or accessory.

ADJUSTMENTS

TO CHANGE THE SPRAY PATTERN (NARROW JET / WIDE SPRAY)

1. Hold the shaft of the lance in one hand.
2. To vary the spray between narrow and wide, turn the nozzle counterclockwise through a half-of-a-turn (180°).
   

ADJUSTING THE PRESSURE

Increasing the distance you are from the surface being cleaned and adjusting the spray to a wider angle (lowers the pressure).

APPLYING CHEMICALS AND CLEANING AGENTS

To improve the cleaning performance, you can introduce chemical cleaning agents (detergents) to the water jet using the detergent bottle attachment. This is particularly useful when washing cars, greasy engine parts, or removing oil spots on concrete etc.

CAUTION: IF YOUR EYES COME INTO CONTACT WITH ANY CLEANING FLUIDS, RINSE THEM IMMEDIATELY WITH PLENTY OF FRESH CLEAN WATER AND SEEK MEDICAL ADVICE IF REQUIRED.

To prepare for detergent application:

1. Remove the lance if fitted and connect the detergent bottle assembly to the gun as shown
2. Remove the detergent bottle and fill with detergent.
   • Only use detergents recommended for use with pressure washers such as
     CLARKE Traffic Film Remover for car cleaning, patio cleaning etc., or CLARKE Wash & Wax, both available from your CLARKE dealer. DESCRIPTION| SIZE| PART NUMBER
     ---|---|---
     Car Wash & Wax Shampoo| 5 Litre| 3050815
     Concentrated Traffic Film Remover| 5 Litre| 3050821
     Concentrated Traffic Film Remover| 25 Litre| 3050820
     Ready To Use Traffic Film Remover| 5 Litre| 3050818
     Ready To Use Traffic Film Remover| 25 Litre| 3050819
3. Replace the bottle.
4. Use the pressure washer as normal.
   NOTE: When using the detergent bottle the pressure will be much lower then normal.

SHUTTING DOWN

When you have finished using the pressure washer, follow the procedure shown below to switch off and disconnect the unit.

1. Set the switch to the OFF position.

2. Turn off the water supply at the tap.

   • To release the pressure in the machine, pull and hold the trigger until no more water comes out of the nozzle.
     

3. Engage the trigger lock.

4. Disconnect from the power supply.

5. Wind the hose onto the reel and put the spray gun/lance into the holder on the power washer.
   

STORAGE PROCEDURE

Disconnect from the water supply, and ensure the system is completely drained when not in use.

Store in a cool dry location. Avoid storing the power washer at freezing temperatures.

Residual water in the high pressure pump of hose assembly may cause permanent damage to the components if it freezes.

MAINTENANCE

WARNING: REMOVE THE PLUG FROM THE SOCKET-OUTLET BEFORE CLEANING OR MAINTENANCE AND WHEN REPLACING PARTS

CLEANING THE NOZZLE

If the nozzle becomes partially clogged with foreign material such as dirt or lime scale, excessive pressure may develop and the pump pressure will pulsate. Clean the nozzle immediately as follows:

1. Turn off the power washer and turn off the water supply.
2. Pull the trigger to relieve any water pressure.
3. Disconnect the lance from the spray gun.
4. Remove any obstructions by directing the water supply into the end of the lance for 30 seconds to back flush loose particles.
5. If flushing does not dislodge the obstruction, carefully use the nozzle cleaning tool, to clear the nozzle.
6. Reconnect the lance to the gun and turn on the water supply.

CLEANING THE WATER INLET FILTER

This filter should be checked periodically and cleaned if necessary.

1. Remove the inlet filter from the pressure washer as shown.
2. Clean the filter by flushing both sides with water.
3. Replace the filter into the water inlet.
   • The tapered side faces in.
     
     NOTE: Do not operate the pressure washer without the filter installed.

TROUBLESHOOTING

is topped up.
Water filter dirty.| Clean or replace.
Water temperature is too high| Make sure the water supply is below 40 degrees.
Motor suddenly stops.| Thermal protection has activated due to overheating.| Switch off the machine and wait until the unit has cooled down sufficiently.
Pressure fluctuations or pressure drop.| Shortage of water.| Turn water tap on fully.
No water due to clogged inlet filter.| Clean water inlet filter.
Motor does not start when switched on.| Plug is not connected properly.| Check plug and lead and have them replaced by a qualified electrician if necessary.
Mains fuse tripped/blown.| Renew fuse or reset.
Motor hums when trigger operated and does not start.| Mains voltage too low.| Have electrical connection checked.
Motor cuts out.| Motor protection switch has been activated.| Switch off and allow to cool for at least 15 minutes.
Nozzle partly clogged.| Clean using the supplied nozzle cleaning needle.
Additives are not being supplied.| Detergent container is empty.| Fill detergent container.
High Pressure is selected.| Set the lance to LOW pressure.

PRODUCT SPECIFICATIONS

INTERNATIONAL
Hemnall Street, Epping, Essex CM 16 4LG

DECLARATION OF CONFORMITY
This is an important document and should be retained.

Product Description: Power Washer
Model number(s): Jetstar 1850
Serial / batch Number: 7336005
Date of Issue: 16/06/2021
(Noise Conformity)
Notified Body: n/a
Technical Documentation Holder: A.R.Pond Clarke International 2a Shrubland Road London E10 7RB UK
Conformity Assessment Procedure: to 2000/14/EC Annex V
Manufacturer: Clarke International
Noise Related Value: 360 L/h
Measured Sound Power Level: 93 dB
Guaranteed Sound Power Level: 96 dB

We hereby declare that this product(s) complies with the following statuary requirements:

Electromagnetic Compatibility Regulations 2016.
Supply of Machinery (Safety) Regulations 2008.
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
The Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001.

The following standards have been applied to the product(s):

EN 60335-1:2012+A11:2014, EN 60335-2-79:2012, EN 62233:2008, EN 55014-2:2015, EN 55014-1:2006 +A1:2009+A2:2011, EN 61000-3-2:2014, EN 61000-3-3:2013.

The technical documentation required to demonstrate that the product(s) meet(s) the requirement(s) of the aforementioned legislation has been compiled and is available for inspection by the relevant enforcement authorities.

The UKCA mark was first applied in: 2021

**Signed:

**

ASSOCIATED PRODUCTS

| Traffic Film Remover, 5 Litres Concentrate Part Number: 3050821
---|---

| Traffic Film Remover, 25 Litres Concentrate Part Number: 3050820

| Traffic Film Remover, 5 Litres Ready to Use Part Number: 3050818

| Traffic Film Remover, 25 Litres Ready to Use Part Number: 3050819

| Car Wash & Wax Shampoo, 5 Litres Part Number: 3050815

QUALITY PRODUCTS

AIR COMPRESSORS
From DIY to industrial, Plus air tools, spray guns and accessories.

GENERATORS
Prime duty or emergency standby for business, home and leisure.

POWER WASHERS
Hot and cold, electric and engine driven – we have what you need

WELDERS
Mig, Arc,Tig and Spot. From DIY to auto/industrial.

METALWORKING
Drills, grinders and saws for DIY and professional use.

WOODWORKING
Saws, sanders, lathes, mortisers and dust extraction.

HYDRAULICS
Cranes, body repair kits, transmission jacks for all types of workshop use.

WATER PUMPS
Submersible, electric and engine driven for DIY, agriculture and industry.

POWER TOOLS
Angle grinders, cordless drill sets, saws and sanders.
STARTERS/CHARGERS
All sizes for car and commercial use.

PARTS & SERVICE

0208 988 7400
Parts Enquiries
Parts@clarkeinternational.com
Servicing & Technical Enquiries
Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
alann, .111111-a11111 INTERNATIONAL Hemnall Street, Epping, Essex CM16 4LG

www.clarkeinternational.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>