MiNOSTON MP26Z Z-Wave Mini Smart Plug Instruction Manual

: August 8, 2024
: Minoston

Table of Contents

MiNOSTON MP26Z Z-Wave Mini Smart Plug
Speciﬁcation
Features
Troubleshooting
Power-on Status
Adjust LED Brightness
FCC / IC
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MiNOSTON MP26Z Z-Wave Mini Smart Plug

Speciﬁcation

Input : 125VAC 60Hz
Frequency : 908.42 MHz
Loading : 15A 1875W RESISTIVE OR GENERAL PURPOSE 10A MAX 1250W TUNGSTEN 1/2 HP
Temperature Range: 32° F~104° F

Features

Z-Wave control on/oﬀ.
Z-Wave controlled AC outlet for standard incandescent lighting, CFL/LEDs, fans, or small appliances(1875W Resistive Max).
Grounded 3-wire power connection for safety.
Remembers and restores on/oﬀ status after power failure.
Built-in Z-Wave Plus signal repeater to extend network range.
S2 security and 800 Z-Wave chip for reliable wireless communication.
Work with most of Z-Wave controllers.

This product can be included and operated in any Z-Wave network with other Z -Wave-certiﬁed devices from other manufacturers and/or other applications. All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network. This Device supports Lifeline (association group 1) supporting 1 node for lifeline communication. Group 1 must be assigned the Node ID of the primary controller where unsolicited notiﬁcations will be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline Association only supports the “Device Reset Locally” function.

Add the Device to the Z-Wave Network with a QR Code

Plug In the Smart Plug: Insert the Z-Wave smart plug into a power outlet.
Note:
Plug directly into the outlet. Do not use with power strip.
The device may need to be within 100 feet of the z-wave controller to pair. Therefore, it is recommended to move the device within 100 feet of the controller, and then relocate it to the desired location in your home once paired. If the device is included in this way, be sure to refresh the network.
Refer to your speciﬁc Z-Wave hub or controller’s instructions to enter inclusion mode.
Put the device in Inclusion Mode: Scan the QR on the device and then press the button (left/right) 3 times quickly.
Wait for Pairing Conﬁrmation: The Z-Wave controller should detect the smart plug, and you may receive a conﬁrmation on the controller. Conﬁrm it to complete the settings.

Troubleshooting

If the device does not enter pairing mode (the LED indicator does not blink), press the device button 3 times faster.
If the device does not enter pairing mode (the LED indicator does not blink) even after pressing the device button 3 times faster, reset the device by pressing the button twice quickly then hold a 3rd press for 10 seconds.
If the reset fails, exclude the device from your Z-Wave hub (z-wave exclusion).
If the z-wave controller does not ﬁnd the device, bring the device as close as possible to your z-wave controller and re-add the device. After the network conﬁguration is completed, the device can be moved to the location you want.
Special reminder for users that connected the device with SmartThings or Hubitat:
For SmartThings: If your z-wave controller is SmartThings, be sure to install the edge driver by following the steps to solve the problem of abnormal usage.
Scan the above QR code(left)to open the SmartThings Edge Driver subscription channel of the product.
Log in to the SmartThings account after opening the SmartThings Edge Driver subscription channel.
Select the SmartThings Hub you are using, and click “Enroll”.
After “Enroll” is completed, click “Available Drivers”.
After entering the “Available Drivers” page, select “Z-Wave Switch” to “Install”. After installing our eedgedriver, please remove the device from your hub and re-add it. Note: Please scan the QR code on the right to view the guide video.
For Hubitat: A device handler is needed for this device. Please download it from www.minos-ton.com.

Add Z-Wave Long Range with QR Code
The device is compatible with SmartStart. SmartStart-enabled products can be added to a Z-Wave network by scanning the Z-Wave QR Code found on the top of the outlet or the back of the box with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on and in the network vicinity.

Note: Z-Wave Long Range device can only support be included via SmartStart. Extract the DSK from the end device and paste it into the DSK Value in the PC Controller, make sure the “Long Range” option is ticked.

Return Factory Defaults

Manually reset: Press the button twice quickly then hold a 3rd press for 10 seconds.
Host reset: After being removed from the host, the device is restored to factory settings.

Remove the Device

Follow the instructions for your Z-Wave-certiﬁed controller to remove a device from the Z-Wave network.
Once the controller is ready to remove your device, press the manual button on the left/right smart plug 3 times quickly.

Association Group
The device supports 3 groups and each group supports up to 5 devices.

Group 1 Lifeline

Group 2 Left outlet sends a basic set
Group 3 right outlet sends a basic set

Please contact us if you have any questions:

Parameter Settings

LED Indicator Status
This parameter can set the status of the indicator light when the device is turned on or oﬀ. Operation: Press the manual button 6 times quickly to change parameters.

Parameter =1, size =1byte, value=00(default) Led on when outlet on
Parameter =1, size =1byte, value=01 Led off when outlet on
Parameter =1, size =1byte, value=02 LED always ON
Parameter =1, size =1byte, value=03 LED always OFF

Timer Auto-off
This parameter can set a timer to turn off the device automatically. The value entered in the parameter corresponds to the number of minutes.

Operation: Set up in the z-wave hub.
Parameter =2, Size=4byte, Values:0-65535 (Min) auto-oﬀ the left outlet Parameter =3, Size=4byte, Values:0-65535 (Min) auto-oﬀ the right outlet
Value=0(default) disable

Timer Auto-on

This parameter can set a timer to turn on the device automatically. The value entered in the parameter corresponds to the number of minutes.

Operation: Set up in the z-wave hub.
Parameter =4, Size=4byte, Values: 0 – 65535 (Min) auto-on the left outlet
Parameter =5, Size=4byte, Values:0 – 65535 (Min) auto-on the right outlet

Power-on Status

This parameter can set the power condition of the outlet after the device is powered on. Operation: Press the manual button 10 times quickly to change the parameter. Parameter=6，Size=1byte

Value=0 Output is always oﬀ
Value=1 Output is always oﬀ
Value=2 Memory last status(default)

Adjust LED Brightness

This parameter can set the brightness of the device’s LED indicator. Operation: Press the manual button 8 times quickly to change the parameter.

Parameter=7, Size=1byte
Value=0 Bright
Value=1 Medium
Value=2 Low (default)

GENERIC DEVICE CLASS
0x10 – SWITCH BINARY

SPECIFIC DEVICE CLASS
0x00 – NOT_USED

COMMAND CLASSES

COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SWITCH_BINARY_V2 COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_TRANSPORT_SERVICE_V2 COMMAND_CLASS_VERSION
COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_INDICATOR
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_MULTI_CHANNEL_V4 COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5 COMMAND_CLASS_CONFIGURATION_V4

FCC / IC

This device complies with part 15 of the FCC and Industry Canada license- exempt RSS standard(s). Operation is subjected to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by modiﬁcations to this equipment. Such modiﬁcations could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.

Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void the user’s authority to operate the device.

CAUTION – PLEASE READ!
This device is intended for installation by the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada If you are unsure or uncomfortable about performing this installation consult a qualiﬁed electrician.

WARNING
RISK OF FIRE / RISK OF ELECTRICAL SHOCK / RISK OF BURNS TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS PRODUCT HAS A GROUNDING-TYPE PLUG THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING-TYPE POWER OUTLET. IF THE PLUG DOES NOT FIT INTO THE OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. DO NOT CHANGE THE PLUG IN ANY WAY. CONTROLLING APPLIANCES:

CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT

DO NOT EXCEED RATINGS
DO NOT USE TO CONTROL ANY DEVICE

WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP ETC.)

MEDICAL EQUIPMENT
Please DO NOT use this switch to control Medical or Life Support equipment. Z-Wave devices should never be used to control the On / Oﬀ status of Medical and/or Life Support equipment.

CONTROLLING APPLIANCES
Please exercise EXTREME CAUTION when using Z-Wave devices to control appliances. The reason is that the appliance you want to control may be in a separate room and if unintentional behavior occurs (such as a device turning on or oﬀ – either intentionally via schedules or unintentionally via network error) this event may lead to a hazardous condition. For these reasons, please note the following suggestions:

Do not include Z-Wave devices in Groups or Scenes if they control appliances.
Do not use Z-Wave devices to control electric heaters or any other appliances that may present a hazardous condition due to unattended, unintentional, or automatic power control.