JONATHAN Y JYL7569A Flush Mount Ceiling Fixture User Guide
- October 30, 2023
- JONATHAN Y
Table of Contents
JONATHAN Y JYL7569A Flush Mount Ceiling Fixture
Product Information
This product is a lighting fixture with model number JYL7569A and
dimensions 18D X 9.5H. It includes a mounting plate, body, bulb, glass shade,
screws, wire connectors, and other hardware required for installation. The
product is designed for indoor use only and supports a maximum of four bulbs
with a wattage no greater than 40 watts for on/off type bulbs or 9 watts for
LED bulbs. It is recommended that the installation of this lighting fixture be
done by a licensed electrician. Before installation, the main electrical
supply from the main fuse box/circuit breaker should be switched off. The item
should be inspected carefully before attempting to install. If there is any
damage or obvious defect, do
not install it. The item may not be returned once it has been installed.
Product Usage Instructions
-
Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated assembly time: 20 minutes.
-
Secure mounting plate (A) to outlet box with mounting screws (B).
-
Make wire connections, with wire connectors(D), following the reference chart listed in the manual.
-
For grounding instructions:
-
For installation in the United States: Wrap ground wire from the outlet box around the green ground screw(C) on the mounting plate, no less than 2 inches from the wire end. Tighten the ground screw. If the fixture
is supplied with a ground wire, connect it to the outlet ground wire with a wire connector. -
For installation in Canada: If the fixture is supplied with a ground wire, wrap the ground wire around a green grounding screw on the mounting plate. Tighten the ground screw.
-
-
Attach the lamp body (F) to the mounting plate (A) and secure it with a retaining screw (E).
-
Install bulb(H). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that the electrical current is turned off before changing bulbs.
-
Attach the glass shade(I) to the socket and then fix it using the screws(G).
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED
ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT THE ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED
CARE AND MAINTENANCE
To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only dry soft cloth to dust or wipe carefully
NOTICE& IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
- he external flexible cable or cord of this luminaire cannot be replaced
- if the cord is damaged, the luminaire shall be destroyed
Part List and Hardware List
PREPARATION
Before beginning assembly of the product, make sure all parts are present.
Compare parts with package contents list and hardware contents list. If any
part is missing or damaged, do not attempt to assemble the product. Estimated
Assembly Time: 20 minutes.
- Secure mounting plate (A) to the outlet box with mounting screws (B).
- Make wire connections, with wire connectors(D), following the reference chart listed below.
Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )Grounding Instructions:
For installation in the United States: Wrap ground wire from the outlet box around the green ground screw(C) on the mounting plate, no less than 2″ from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect to the outlet ground wire with a wire connector. For installation in Canada: If the fixture is supplied with ground wire, wrap the ground wire
around the green grounding screw on the mounting plate. Tighten the ground screw.Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
---|---
Black| White
- Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)|
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
|
Insulated Wire (not green) with Silver metal conductor.
- Attach the lamp body (F) to the mounting plate (A) and secure with a retaining screw (E).
- Install bulb(H). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
- Attach the glass shade(I) to the socket and then fixed using the screws(G).
PLEASE USE ON/OFF TYPE”A” BULB MAX 40-WATT OR LED BULB MAX 9 -WATT THERE ARE LED 4PCS 4WATT BULBS IN THE BOX
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>