JONATHAN Y JYL7586A LED Pendant Lamp Instruction Manual
- June 12, 2024
- JONATHAN Y
Table of Contents
JONATHAN Y JYL7586A LED Pendant Lamp
Product Information
- Model #: JYL7586A
- Product Dimensions: 12Dx23-95H
- Estimated Assembly Time: 20 minutes
- Maximum Bulb Wattage: Type A Bulb – 60W, CFL Bulb – 13W, LED Bulb – 9W
Product Usage Instructions
- WARNING: We recommend installation of this lighting fixture be done by a licensed electrician.
- WARNING: Switch off the main electrical supply from the main fuse box/circuit breaker before installation.
- Inspect the item carefully before attempting to install. If there is any damage or obvious defect, do not install. The item may not be returned once it has been installed.
- Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
- Attach the mounting bar (A) to the junction box with the outlet box screw (C).
- Connect the fixture body (J) and rod (H) together with the lock link (I). Attach the metal chain (G) to the canopy unit (F) on the top and to the rod (H) on the bottom.
- Connect wires according to the following instructions:
- Connect Hot, Black or Red Outlet Supply Wire to Black Parallel Cord (round & smooth).
- Connect Neutral, White Outlet Supply Wire to White Parallel Cord (square & ridged).
- Connect Clear, Brown, Gold or Black without Tracer (colored stripes) to Insulated Wire (not green) with copper metal conductor.
- Connect Clear, Brown, Gold or Black with Tracer (colored stripes) to Insulated Wire (not green) with Silver metal conductor.
- Note: When parallel wire (SPT I & SPT II) is used, the neutral wire is square shaped and ridged, and the hot wire will be round in shape and smooth.
- Grounding Instructions:
- For installation in the United States: Wrap the ground wire from the outlet box around the green ground screw (B) on the mounting bar, no less than 2 inches from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire nut.
- For installation in Canada: If the fixture is supplied with a ground wire, wrap the ground wire around the green grounding screw on the mounting bar. Tighten the ground screw.
- Raise the canopy unit (F) and thread it to the outlet box screws. Secure it with the canopy nut (E).
- Install the light bulb (K) to the socket. Please use a Type A Bulb max 60W or CFL Bulb max 13W or LED Bulb max 9W. There is 1PC LED 4W Bulb in the box.
- Enjoy your lamp!
Model#: JYL7586A
Product Dimensions: 12″Dx23″-95″H
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED
ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE
BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN
INSTALLED.
CARE AND MAINTENANCE
To clean the outside of the fixture, use a dry or slightly dampened clean
cloth (use clean water, never a solvent) to wipe the surface of the fixture.
To clean the inside of the fixture, first disconnect power to the fixture by
turning off the circuit breaker or by removing the fuse at the fuse box. Next,
use a dry or slightly dampened clean cloth (use clean water, never a solvent)
to wipe the interior surface of the fixture.
Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a
dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
The external flexible cable or cord of this lamp cannot be replaced
If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
- Attach the mounting bar (A) to the junction box with outlet box screw (C).
- Connect the fixture body (J) and rod (H) together with lock link (I), attach the metal chain (G) to the canopy unit (F) on the top and to the rod (H) on the bottom.
- Connect wires.
Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
---|---
Black| White
- Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)
|
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
|
Insulated Wire (not green) with Silver metal conductor.
Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is
square shaped and ridged and the hot wire will be round in shape and smooth. (
See Illustration on left. )
Grounding Instructions:
* For installation in the United States: Wrap ground wire from outlet box around green ground screw(B) on mounting bar, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire nut.
* For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bar. Tighten ground screw.- Raise the canopy unit (F) thread to the outlet box screws, secure with canopy nut (E).
- Install the light bulb (K) to the socket.
PLEASE USE TYPE”A” BULB MAX 60-WATT OR CFL BULB MAX 13-WATT OR LED BULB MAX 9-WATT,THERE IS 1PC LED 4-WATT BULB IN THE BOX
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>