JONATHAN Y JYL9918 Cillian 27 Inch 6-Light Brass Gold-Clear Mid-Century Modern Iron LED Chandelier Instruction Manual
- June 12, 2024
- JONATHAN Y
Table of Contents
JONATHAN Y JYL9918 Cillian 27 Inch 6-Light Brass Gold-Clear Mid-Century
Modern Iron LED Chandelier
Product Information
- Model: JYL9918
- Product Dimensions: 27″ x 27″ x 20.5″-50.5″H
Part List
- Lamp Body (B)
- Mounting Plate (F)
- Canopy Nut (I)
- Shade (J)
- Bulbs (K)
Hardware List
- Parallel Cord (round & smooth)
- Parallel Cord (square & ridged)
- Ground Wire
- Wire Connector
- Canopy
- Lamp Cap
- Lamp Bulbs (6 x 4W LED bulbs included)
Grounding Instructions
For installation in the United States:
- Wrap the ground wire from the outlet box around the green ground screw on the mounting bracket, leaving at least 2 inches from the wire end.
- Tighten the ground screw.
- If the fixture is supplied with a ground wire, connect it to the outlet ground wire using a wire connector.
For installation in Canada:
If the fixture is supplied with a ground wire:
- Wrap the ground wire around the green grounding screw on the mounting bracket.
- Tighten the ground screw.
Product Usage Instructions
- Make sure the electrical current is turned off before starting the installation process.
- Attach the Canopy (included) of the Lamp Body (B) to the Mounting Plate (F) and fix it by turning the Canopy Nut (I) clockwise.
- Install the Shade (J) on the lamp cap of the Lamp Body (B).
- Insert the bulbs (K) into the sockets. Ensure that you use light bulbs with wattage no greater than specified on this fixture.
- For this product, please use Type B bulbs with a maximum wattage of 40W or CFL bulbs with a maximum wattage of 13W, or LED bulbs with a maximum wattage of 9W. There are 6 x 4W LED bulbs included in the box.
- After installation and bulb insertion, turn on the electrical current to enjoy your lamp.
Note: If you have any questions or encounter any difficulties during the installation process, please refer to the user manual or contact our customer support for assistance.
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED
ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN
FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL.
IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE
RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE
- To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
- To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slighly damperned clean clorth (use clean water, never a solvent) to wipe the interior surface of the fixture.
- Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
- The external flexible cable or cord of this luminaire cannot be replaced
- If the cord is damaged, the luminaire shall be destroyed
Part List and Hardware List
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is
missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
- Separate the Mounting Plate(F) from the Canopy(G) by removing the Canopy Nut( I ) anti-clockwise.
- Fix one end of the Finial (A) to the Lamp Body (B).
- Fix the Long Tube (C), Short Tube (D) and Canopy(E) to the Lamp Body (B) in turn.
- Attach the Mounting Plate (F) onto the J-box and secure it by turning 2 Mounting Screws (H) clockwise till tight.|
Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
---|---
Black| White
- Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored| Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor| Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions:
* a) For installation in the United States: Wrap ground wire from outlet box around green ground screw on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
* b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
- Attach the Canopy of the Lamp body(B) to the Mounting Plate (F) and fix it by turning the Canopy Nut ( I ) clockwise.
- Install the Shade (J) on the lamp cap of the Lamp Body (B)
- Insert the bulbs (K) into the Sockets. Be sure to use light bulb(M) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
PLEASUE USE TYPE”B” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED MAX 9-WATT THERE ARE 6 X 4W LED BULBS IN THE BOX. ENJOY YOUR LAMP
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>