KSE-LIGHTS KS-8001 SUPAHERO Hand Lamp Instruction Manual
- June 12, 2024
- KSE-LIGHTS
Table of Contents
KSE-LIGHTS KS-8001 SUPAHERO Hand Lamp
HAND LAMP KS-8001 & KS-8001-0S & KS-8001-DS
PRODUCT OVERVIEW
The product complies with the following standards:
EN 60079-0 :2018 IEC 60079-0:2017, Ed. 7
EN 60079-11:2012 IEC 60079-11:2011, Ed. 6
EN 60079-28:2015 IEC 60079-28:2015, Ed. 2
IBExU20ATEX 1130 X – IECEx IBE20.0032 X
Special conditions for use in the Ex-atmosphere:
The hand lamp can be used in an extended ambient temperature of -15 °C to +50
°C
Damaged equipment must be taken out of service immediately and out of
potentially explosive atmosphere.
The hand lamp may only be charged outside the hazardous area using the
appropriate charger.
The light window must never be completely covered during operation in a
potentially hazardous area.
FEATURES
400/315/140/(270) lumens
240/190/85/(165) meters
6000 Kelvin
POWER-/ mode#2/ mode#3/
(flashlight)
300/240/110/(205) meters
smoke light
3,5/4,5/10,5/(11) hours
380 grams
<11 hours charging
IP68
80% capacity after 800 cycles
emergency light
FIRST USE
The hand lamp must be fully charged before first use. To do this, connect the charger to a suitable power source and push the lamp into the charger. Make sure that the lamp is fully inserted into the charger.
Now a red charging status LED in the lamp will light up constantly. This diode signals an active charging process. As soon as the charging process is completed, the red LED goes out and a green LED lights up constantly. The lamp is now fully charged. Please read the safety regulations regarding charging.
After the lamp has been fully charged, the lamp can be switched on using the on/off button.
By pressing the button several times, the individual modes are switched through as described. After the last mode, the lamp switches off.
The lamp has a display that indicates the current battery level. The display is always activated for 15 seconds after the lamp is switched off. The battery status is divided into 3 levels: green=> 70% orange= >30 to 70% red= <30 To determine the battery status as accurately as possible, leave the light on for at least 10 seconds.
The lamp may be used and recharged at any time without negatively affecting the battery.
If the lamp is connected to the charger when it is switched on, the emergency light function is activated. When the charging process starts, the light goes out. If the mains voltage is now disconnected, the light switches on automatically and thus ensures an illuminated environment during the emergency situation.
The lamp is resistant to oil, grease, glue, hydrocarbon, turpentine substitute and various cleaning agents.
Wash the lamp body and the windscreen with lukewarm soapy water. Do not use acid or abrasive cleaners, especially not on the windscreen.
Do not use a high-pressure hose! Technical maintenance or repair may only be carried out by KSE-LIGHTS or an authorised person.
KSE-LIGHTS gives a two-year warranty on the product for material and manufacturing defects. Excluded from the guarantee are normal wear and tear, oxidation, changes, improper use, storage and maintenance as well as damage caused by negligence or use for which the product is not intended.
The warranty on the accumulator lasts for three years. If the serial number is removed, the warranty is immediately void. Customer service in the event of a warranty claim, please return the lamp to the dealer with proof of purchase. It will be repaired or replaced.
Do not open the lamp or charger under any circumstances. Do not use or recharge the lamp if it is defective. No warranty claims can be made for consequential damage caused by defective parts. Failure to do so will invalidate the warranty and the operational safety.
To replace the accumulator, purchase article KS-2335 with additional instructions for replacement on your own.
KSE-LIGHTS accepts no liability for direct, indirect and accidental consequences, as well as any other form of damage due to the use of this product.
SAFETY INFORMATIONS
Do not use damaged lamps, chargers or sockets to charge the lamp.
Never place the switched-on lamp on the light window when working in potential dangerous atmosphere.
Do not pull the power cord to remove the plug out of the socket.
Only use original KSE-LIGHTS chargers.
The use of other chargers may adversely affect the life of the product. KSE- LIGHTS is not responsible for consequential damage, if parts are used which are not authorised by KSELIGHTS.
Protect the charger and accumulator from damage.
Never store the products outside the approved temperature range from 0°C to +45°C.
Never charge the product outside of the approved temperature range from 0°C to +35°C.
TROUBLE SHOOTING
When using the hand lamp and charging adapter some malfunctions or operator failures can appear, here are the solutions:
The hand lamp can not be turned on. Insert the lamp into the charger and try again. Should the Lamp still show no response, please contact our product service.
The lamp shows no response to insertion in the charger.
Disconnect the charger from the supply voltage and try again. Should the lamp still show no reaction, please contact our product service.
Both charge indication LEDs are turned on.
The lamp is fully charged and the charging controller has switched to standby mode. Remove the lamp from the charger, switch on shortly and insert again. Now only one LED should light up. Repeat the process if both LEDs are still turned on.
After the lamp is fully charged, the green charging indication LED turns off.
Solution: The lamp is fully charged and the charger has switched to standby mode. Remove the lamp shortly out of the charger, switch on shortly and replace back in the charger.
Now an indication LED should light up again.
Declaration of Conformity
CHARGER KS-5800 & KS5810 & KS-5836
PRODUCT OVERVIEW
FIRST USE
- Insert the hand lamp in the charger as shown in the picture.The status LED inside the lamp is red. When the status LED turns to green, the lamp is fully charged.
- Please make sure, that there are no objects between the charger and the hand lamp.
- The hand lamp can be charged and recharged anytime.
FEATURES
KS-5800
AC 110 – 230V , 50/60Hz incl. EU/UK/AU/US 
KS-5810
DC 12-24V / for vehicle
KS-5836
DC 9-36V for installation
SAFETY INFORMATIONS
Do not use damaged lamps, chargers or power sockets to charge the lamp. Do not pull the power cord to remove the AC adapter. Only use original KSE-LIGHTS chargers. The use of other chargers may have a negative effect on the life of the product. KSE-LIGHTS is not liable for consequential damage if parts are used which are not approved by KSE-LIGHTS.
Protect the charger and the accumulator from damage.
Never charge the product outside the approved temperature range from 0°C to +35°C.
The supply voltage of the charger can be provided by one of the following measures according to IEC 60079-14:
- where Um does not exceed 50 V AC or 120 V DC, in a SELV or PELV system
- via a safety isolating transformer complying with the requirements of IEC 61558-2-6 or a technically equivalent standard
- directly connected to apparatus complying with the IEC 60950 series, IEC 61010-1 or a technically equivalent standard
- fed directly from cells or batteries
CUSTOMER SUPPORT
+49 (0)2333 982 47 30
www.shop.kse-lights.com
www.kse-lights.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>