Chargers S15 2 In 1 MagSafe Car Charger User Guide

Chargers S15 2 In 1 MagSafe Car Charger

Product Information The product is a device that complies with Part 15 of the FCC Rules. It is designed to operate within FCC radiation exposure limits for an uncontrolled environment. The device should be installed and operated with a minimum distance of 20cm between the radiator and the user’s body. It is important to note that an changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment.

Product Usage Instructions

1. Ensure that the device is placed at least 20cm away from your body during operation.
2. Do not make any changes or modifications to the device without prior approval from the responsible party for compliance.
3. Avoid operating the device in conjunction with any other antenna or transmitter.
4. The device should not cause harmful interference. If it does, try repositioning it or contacting customer support for assistance.
5. The device must accept any interference received, including interference that may cause undesired operation. If you experience any issues, try adjusting the device’s placement or contact customer support for further guidance.
6. Follow all other instructions provided in the user manual for optimal and safe usage of the product.

Thank you for purchasing and using this product!
Please read this operation instruction carefully before using this product.

Product Specification

2 in 1 MagSafe Car Charger

• Input: SV=3A/9V=A Cell Phone
• Output: 7.SW Watch
• Output: 3W Charging
• Efficiency: 80%

Applicable Devices

Compatible with MagSafe iPhone and Apple Watch.

The LED light turns red during wireless charging to indicate a charging failure.

The following situation can cause failures, like charging slowly, stop charging, over-temperature for charging position.

1. The adapter is not run up to standard (No PC USB output power supply)_
2. The charging cable is not up to standard.
3. The phone case is too thick ( within 2mm thickness phone case is recommended ).
4. The built-in wireless charging receiver position does not coincide with wireless charger coil position.
5. There is metal/magnet on the back of cell phone or phone case.
6. The smartphone does not support wireless charging function.

Attention

1. Please keep the charger away from water or other liquid.
2. If you need to clean the charger, please make sure it is not connected to power supply.
3. Operating temperature: -20~45’C.

Product Description

1. Semiconductor cooling technology makes the phone fully charged quickly in about 2.5 hours.
2. Use your driving time to charge your iPhone and Apple Watch, and eliminating low battery anxiety.

Step to install air vent

1. Follow the arrows to install 3 parts.

2. Adjust the screw cap to the best active status.

3. Turn the pulley to the left to adjust the hook to the longest.

4. Rotate the pulley to the right to make the hooks to clamp the air vent blades.

5. Installation completed.

Wireless Charger Operation

Insert the watch charger into the host.

Input:
Connect the wireless charger and car adapter with the charging cord.

LED indicator light

White LED Light: Standby.
Blue LED Light: Charging normally. Red LED Light: Charging abnormally.

MagSafe Usage

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>