snoozeband MAX 2BHWR-MAX Sleep Headphones User Manual
- August 17, 2024
- snoozeband MAX
Table of Contents
snoozeband MAX 2BHWR-MAX Sleep Headphones
Bluetooth sleep headphones with built-in relaxing music and automatic switch- off timing function
Using Instructions
Eyecup fixation
- Place eyecups inside the eyelets.
- Turn the eyecups 90 degrees.
Headphone positioning
- Open pocket at the back.
- Move headphones in the right position for your ears
- Press the white side of the speaker on the white velcro fabric to secure the position.
Removal for washing
- Displace the headphones away from the velcro section.
- Remove the eyecups.
- Open the bottom pocket and remove all the electronic components for a safe wash.
Control Buttons
Turning On/Off
- Press and hold for 3 seconds
Pairing with your device
- Turn on Bluetooth
- Turn on the SnoozeBand
- Connect to Snoozeband MAX on your device
A blue and red light will flash while attempting to pair the Snoozeband with
your device. Once paired, the light will stop.
If you want to pair it with a new device next time, make sure it’s
disconnected from the previously paired device.
Charging
The USBC charging port is located on the top of the front control box.
- Plug the USBC charging cable into the charging port and the other end into a power source with ~5V (e.g. phone charger)
- The LED light will turn red whilst charging. It will turn blue as soon as the battery is fully charged (approx. 1-2 hours). Please do not charge longer than 2 hrs to preserve battery life.
LED Indicators
Troubleshooting
How to set a timer
You can set the built-in sleep timer 60 or 120 minutes.
Once enabled, the Snoozeband will power down automatically as you drift off to
dreamland.
- Double press the button to set the timer to 60 minutes, double press again for 120 minutes.
- The corresponding voice prompt will remind you of the timer set.
NOTE
- In Bluetooth mode, if there’s no device connected, the timer will not work. In white noise mode, the timer will always work.
How to use white noise
It comes with 10 soothing sleep sounds, including Ocean waves, White noise, Pink noise, Brown noise etc.
- Double press the – button to enter the White noise mode
- Short press the middle button to play/pause music
- Long press the + and – button to switch between tracks
- Slowly press the + and – button to adjust volume
NOTE: At anytime you can switch between the bluetooth and White noise
mode by double pressing the – button.
In White noise mode, the bluetooth will be disconnected
Washing the SnoozeBand
- Carefully remove the electric components of the Snoozeband before washing by opening the velcro in the bottom
- Handwash with cold water and air-dry
Precautions
- DO NOT expose the product to liquids or moisture
- DO NOT attempt to tamper with the product by dropping, disassembling, opening or scratching etc.
- DO NOT store the product near acidic or alkaline material
- Take out the headphones before washing
- Keep the product away from fire and high temperatures
- Keep the product away from children and animals
- Note: when not used for 3-6 months, charge once.
Features
- Built-in wireless speakers and microphone
- Integrated white noise
- Automatic shut-off timing function
- Rechargeable through USBC cable
FEATURES
Specifications
- Wireless version: V5.2
- Frequency: 2.402 GHz – 2.480 GHz
- Transmission range: 20m/66Ft
- Rated power: RMS 10mW x 2
- Speaker unit: 32/30mm
- Battery: 200mAh rechargeable Li-polymer battery
- Play time: Up to 20 hours
- Charge time: 2 hours
FCC STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
FAQ
- Q: What should I do if I experience interference while using the headphones?
- A: If you experience interference, try the following steps:
- Reorient or relocate the headphones.
- Increase the distance between the headphones and other electronic devices.
- Connect the headphones to a different power source.
- Contact our customer support for further assistance.
- Q: How can I ensure optimal performance of the Snoozeband Max Sleep Headphones?
- A: To ensure optimal performance, follow these tips:
- Charge the headphones regularly.
- Avoid bending or twisting the band excessively.
- Store the headphones in a cool, dry place when not in use.
CONTACT
Distributed by Snoozeband
- Email – contact@snoozeband.co.uk
- Website – snoozeband.co.uk
Made in – China