Lenco LBT-190 Turntable with Bluetooth Transmission User Manual

Model: LBT-190
User manual ­

Turntable with Bluetooth transmission
CAUTION: Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
PRECAUTIONS BEFORE USE
KEEP THESE INSTRUCTIONS IN MIND:

1. Do not cover or block any ventilation openings. When placing the device on a shelf, leave 5 cm (2″) free space around the whole device.

2. Install in accordance with the supplied user manual.

3. Keep the device away from heat sources such as radiators, heaters, stoves, candles, and other heat-generating products or naked flame. The device can only be used in moderate climates. Extremely cold or warm environments should be avoided. Working temperature between 0° and 35°C.

4. Avoid using the device near strong magnetic fields.

5. Electrostatic discharge can disturb the normal usage of this device. If so, simply reset and restart the device following the instruction manual. During file transmission, please handle with care and operate in a static-free environment.

6. Warning! Never insert an object into the product through the vents or openings. High voltage flows through the product and inserting an object can cause electric shock and/or short circuit internal parts. For the same reason, do not spill water or liquid on the product.

7. Do not use in wet or moist areas such as bathrooms, steamy kitchens, or near swimming pools.

8. The device shall not be exposed to dripping or splashing and make sure that no objects filled with liquids, such as vases, are placed on or near the apparatus.

9. Do not use this device when condensation may occur. When the unit is used in a warm wet room with damp, water droplets or condensation may occur inside the unit and the unit may not function properly; let the unit stand in power OFF for 1 or 2 hours before turning on the power: the unit should be dry before getting any power.

10. Although this device is manufactured with the utmost care and checked several times before leaving the factory, it is still possible that problems may occur, as with all electrical appliances. If you notice smoke, an excessive build-up of heat, or any other unexpected phenomena, you should disconnect the plug from the main power socket immediately.

11. This device must operate on a power source as specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company.

12. Keep away from animals. Some animals enjoy biting on power cords.

13. To clean the device, use a soft dry cloth. Do not use solvents or petrol-based fluids. To remove severe stains, you may use a damp cloth with diluted detergent.

14. The supplier is not responsible for damage or lost data caused by malfunction, misuse, modification of the device, or battery replacement.

15. Do not interrupt the connection when the device is formatting or transferring files. Otherwise, data may be corrupted or lost.

16. If the unit has a USB playback function, the USB memory stick should be plugged into the unit directly. Don’t use a USB extension cable because it can cause interference resulting in failure of data.

17. The rating label has been marked on the bottom or back panel of the device.

18. This device is not intended for use by people (including children) with physical, sensory, or mental disabilities, or a lack of experience and knowledge unless they’re under supervision or have received instructions about the correct use of the device by the person who is responsible for their safety.

19. This product is intended for nonprofessional use only and not for commercial or industrial use.

20. Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position vibrations or shocks or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.

21. Never remove the casing of this device.

22. Never place this device on other electrical equipment.

23. Do not allow children access to plastic bags.

24. Only use attachments/accessories specified by the manufacturer.

25. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as the power supply cord or the plug, when liquid has been spilled or objects have fallen into the device, when the device has been exposed to rain or moisture, does not operate normally, or has been dropped.

26. Long exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss.

27. . If the product is delivered with a power cable or AC power adaptor:
    • If any trouble occurs, disconnect the AC power cord and refer servicing to qualified personnel.
    • Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the cable’s exit point. Do not place heavy items on the power adaptor, which may damage it. Keep the entire device out of children’s reach! When playing with the power cable, they can seriously injure themselves.
    • Unplug this device during lightning storms or when unused for a long period.
    • The socket outlet must be installed near the equipment and must be easily accessible.
    • Do not overload ac outlets or extension cords.
    • Overloading can cause fire or electric shock.
    • Devices with class 1 construction should be connected to a main socket outlet with a protective earthed connection.
    • Devices with class 2 construction do not require an earthed connection.
    • Always hold the plug when pulling it out of the main supply socket.
    • Do not pull the power cord. This can cause a short circuit.
    • Do not use a damaged power cord or plug or a loose outlet.
    • Doing so may result in fire or electric shock.

28. If the product contains or is delivered with a remote control containing coin/cell batteries:
    • Warning: “Do not ingest battery, Chemical Burn Hazard” or equivalent working.
    • [The remote control supplied with] This product contains a coin/button cell battery. If the battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
    • Keep new and used batteries away from children.
    • If the battery compartment does not close securely, stop using the product and keep it away from children.
    • If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

29. Caution about the use of Batteries:

• The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
• The battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use, storage, or transportation.
• Replacement of a battery with an incorrect type can result in an explosion or the leakage of flammable liquid or gas.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or that leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
• Attention should be drawn to the environmental aspects of battery disposal.

INSTALLATION

•  Unpack all parts and remove protective material.
• Do not connect the unit to the mains before checking the mains voltage and before all other connections have been made.

Deliver Content

1 x Manual|
---|---
1 x Power Adaptor + 1 x CE plug|
1 x UK plug|
1 x USB connection cable|
1 x Platter|
1x Felt Mat|

PRODUCT FEATURES
– 33/45 RPM SELECTABLE TURNTABLE
– BELT DRIVEN SYSTEM
– AUTO-RETURN TONEARM
– LIFT LEVER
– BLUETOOTH TRANMITTER
– RCA LINE-OUT
– DETACHABLE HEADSHELL
– PC LINK: CONNECTION WITH COMPUTER VIA USB PORT FOR TURNTABLE RECORDING
– PITCH CONTROL
– ACCESSORIES INCLUDED:

1. TURNTABLE PLATTER
2. SLIPMAT
3. DUST COVER
4. 45 RPM ADAPTOR
5.  WEIGHT COUNTER
6. AUDIO TECHNICA CARTRIDGE AT-3600L
7. USB CABLE
8. OPERATION MANUAL
9. EXTERNAL POWER ADAPTOR

LOCATION OF CONTROL

1. TURNTABLE PLATTER
2. CENTER SPINDLE
3. HEADSHELL
4. RETURN SWITCH
5. PITCH CONTROL KNOB
6. PLAY/STOP SWITCH
7. 33RPM / 45RPM SPEED SELECTOR
8. TONE ARM
9. BT PAIRING BUTTON
10. BT PAIRING INDICATOR| 11) LIFT LEVER
11. ANTI SKATE KNOB
12. WEIGHT COUNTER
13. STROBE LIGHT
14. PHONO / LINE SELECTOR
15. RCA LINE-OUT SOCKET
16. USB PORT
17. EXTERNAL POWER ADAPTOR JACK
18. ON/STANDBY BUTTON
19. GROUND TERMINAL
    ---|---

CAUTION: USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL.
WARNING:
– THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
– THE MAINS PLUGS OR AN APPLIANCE COUPLER ARE USED AS THE DISCONNECT DEVICE AND THE DISCONNECT DEVICE SHALL REMAIN READILY OPERABLE.
PRECAUTIONS FOR USE
INSTALLATION

UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.
DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAINS VOLTAGE AND BEFORE ALL OTHER CONNECTIONS HAVE BEEN MADE.
DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS
AROUND THE UNIT FOR VENTILATION.
CONNECTION

1. CONNECT THE EXTERNAL POWER ADAPTOR WITH AN EXTERNAL POWER ADAPTOR SOCKET.
2. PLUG THE EXTERNAL POWER ADAPTOR INTO A SUITABLE MAINS SOCKET
3. PUSH IN THE ON/STANDBY BUTTON ON THE BACK PANEL TO SWITCH ON THE UNIT FROM STANDBY MODE.

OPERATION
– INSTALL THE DUST COVER INTO THE HINGE ON THE UPPER CABINET. – SET THE TURNTABLE PLATTER ONTO THE CENTER SPINDLE.
– ATTACH THE DRIVE BELT: POSITION THE BELT ON THE MOTOR PULLEY, THE DRIVE BELT IS TIGHTENED UNDER THE TURNTABLE PLATTER.
– PLACE THE SLIP MAT ON THE TURNTABLE PLATTER.
– INSERT THE HEADSHELL INTO THE FRONT END OF THE TONEARM, THEN SCREW THE LOCK NUT WITH THE HEADSHELL IS FIRMLY HELD HORIZONTALLY.

INSTALL THE COUNTERWEIGHT
– SLIDE THE COUNTERWEIGHT ONTO THE TONEARM. TWIST IT LIGHTLY AND IT WILL SCREW INWARDS ONTO THE REAR END OF THE TONEARM. EVERY FULL TURN OF THE SCALE RING REPRESENTS AROUND 2.4 GRAMS (+/-0.4 GRAM).
– FOR THE DEFAULT AUDIO-TECHNICA AT-3600L CARTRIDGE, TURN THE COUNTERWEIGHT INWARDS UP TO THE HORIZONTAL LINE ON THE REAR END OF THE TONEARM. – HOLD THE COUNTERWEIGHT WITH ONE HAND, TURN THE SCALE RING TO “3” AGAINST THE INDEX LINE ON THE SHAFT YOUR ANOTHER HAND, AND MAKE SURE NOT TO TURN THE COUNTERWEIGHT, ONLY TURN THE SCALE RING! THE TRACKING FORCE WILL BE AROUND 3.0 GRAMS (+/-0.4 GRAM).
**– IF NECESSARY, TURNING THE COUNTERWEIGHT INWARDS INCREASES THE TRACKING FORCE, WHILE TURNING THE COUNTERWEIGHT BACKWARDS DECREASES THE TRACKING FORCE.
– FOR OTHER CARTRIDGES, YOU CAN ADJUST THE TRACKING FORCE BY TURNING THE COUNTERWEIGHT INWARDS OR BACKWARDS. EACH NUMBER ON THE SCALE RING CORRESPONDS TO AROUND 0.4GRAM OF TRACKING FORCE.
ANTI-SKATING ADJUSTMENT
THE ANTI-SKATE ADJUSTMENT PREVENTS THE TONEARM ASSEMBLY FROM SKIPPING ACROSS THE RECORD FROM THE CENTRIFUGAL FORCE THAT IS CAUSED SPINNING ROTATION OF THE PLATTER. THE ANTI-SKATING CONTROL KNOB SHOULD BE SET TO THE SAME VALUE AS THE STYLUS PRESSURE. FOR EXAMPLE, IF YOUR COUNTERWEIGHT IS SET TO 3 GRAMS THE ANTI-SKATE VALUE SHOULD ALSO BE SET TO 3.
PICKUP SELECTOR
– LINE / PHONO SELECTOR IS LOCATED AT THE BACK PANEL.
– SELECT “PHONO”, AUDIO SIGNAL WILL BYPASS THE INTERNAL PRE-AMPLIFIER WITHOUT ANY PROCESSOR. THEN TURNTABLE HAS TO BE CONNECTED WITH AN EXTERNAL PREAMPLIFIER OR PHONO CONNECTOR OF AN AMPLIFIER IF AVAILABLE FOR MUSIC PLAYBACK.
– SELECT “LINE”, THE AUDIO SIGNAL WILL BE PROCESSED BY AN INTERNAL PRE- AMPLIFIER. TURNTABLE CAN BE DIRECTLY CONNECTED WITH AN ACTIVE SPEAKER OR LINE- IN CONNECTOR OF AN AMPLIFIER FOR MUSIC PLAYBACK.
– REMOVE THE STYLUS PROTECTOR.
– BE SURE THAT THE TONEARM IS BEING DETACHED FROM THE TONE ARMREST PART BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
– PUSH THE LIFT LEVER UPWARD TO RAISE THE TONEARM FROM THE ARM PARK, AND THEN SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO ROTATE.
– PUT DOWN THE LIFT LEVER TO DROP THE TONEARM AND TOUCH THE RECORD GENTLY. PHONO PLAYING STARTS NOW.
– PUSH THE LIFT LEVER UPWARD TO RAISE THE TONEARM FROM THE ARM PARK, NOW THE PLATTER WILL STILL BE ROTATING BUT PHONO PLAYING WILL STOP. TO CONTINUE THE PLAYING, THE USER NEEDS TO PUT DOWN THE LIFT LEVER.
– TURN THE SPEED SELECTOR TO 33RPM OR 45RPM, DEPENDING ON THE RECORD TO BE PLAYED.
– TURN START / STOP SWITCH TO STOP TURNTABLE FROM ROTATING OR RESUME TO WORK.
– STROB DOTS ON THE TURNTABLE PLATTER FOR SPEED CHECKING. UPPER ROWS OF BIGGER DOTS FOR 33RPM, UPPER ROWS OF SMALLER DOTS FOR 45RPM. ADJUST SPEED BY PITCH CONTROL SLIDER (+/-10%) IF NECESSARY. SUITABLE DOTS WILL KEEP STABILISED UNDER STROB LIGHT IF THE SPEED IS CORRECT. – USE THE 45 RPM ADAPTOR IF REQUIRED.
– AT THE END OF THE RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING, TONEARM WILL AUTOMATICALLY RETURN TO THE TONE ARMREST PART.
– TRIGGER THE RETURN SWITCH DURING RECORD PLAYING, TURNTABLE WILL STOP GENTLY AND
TONEARM WILL AUTOMATICALLY RETURN TO THE TONE ARMREST PART.
– SINCE THERE ARE NUMEROUS VINYL MANUFACTURERS, WE DO NOT GUARANTEE AUTO- RETURN
FUNCTION IS APPLICABLE ON ALL VINYL. IF THE TONEARM CAN NOT RETURN AUTOMATICALLY, PLEASE TRIGGER THE RETURN SWITCH TO ACTIVATE AUTO-RETURN
LINE OUT SOCKET & GROUND TERMINAL
– THIS SYSTEM CAN BE CONNECTED WITH AN EXTERNAL DEVICE (EG. AMPLIFIER AND ACTIVE SPEAKER)
BY RCA LINE-OUT SOCKETS AT REAR CABINET.
THERE IS A GROUND TERMINAL AT THE BACK PANEL OF THE TURNTABLE. END-USER CAN CONNECT IT WITH THE GROUND TERMINAL OF THE EXTERNAL AMPLIFIER OR PREAMPLIFIER WITH GND CABLE (NOT INCLUDED) IF NECESSARY.
BLUETOOTH TRANSMITTER
– THIS SYSTEM CAN BE CONNECTED WITH AN EXTERNAL BLUETOOTH SPEAKER FOR WIRELESS MUSIC PLAYBACK.
– SWITCH TO LINE SELECTOR AT THE BACK PANEL.
– PRESS BT PAIRING BUTTON TO CONTROL THE BLUETOOTH TRANSMITTER FUNCTION:
BT PAIRING INDICATOR FLASHING: READY TO CONNECT WITH EXTERNAL BLUETOOTH SPEAKER.
BT PAIRING INDICATOR STAY ON: ALREADY CONNECTED WITH EXTERNAL BLUETOOTH SPEAKER.
BT PAIRING INDICATOR OFF: DISCONNECTED WITH EXTERNAL BLUETOOTH SPEAKER.
– SINCE THERE ARE NUMEROUS BLUETOOTH SOLUTIONS, WE DO NOT GUARANTEE THAT THIS
TURNTABLE CAN SUPPORT ALL BLUETOOTH SPEAKERS FROM EVERY MANUFACTURER. IN CASE THERE IS ANY EXTERNAL BLUETOOTH SPEAKER THAT CAN NOT BE CONNECTED, PLEASE TRY ANOTHER BLUETOOTH SPEAKER AGAIN. OR CONNECT THIS TURNTABLE WITH A WIRED SPEAKER FOR MUSIC PLAYBACK.
POWER SAVING FEATURE
– TO SAVE ENERGY, IF THERE IS NO AUDIO SIGNAL FROM THE TURNTABLE FOR A PERIOD OF OVER AROUND 10 MINUTES, THE POWER FOR THE UNIT WILL BE CUT. TO ACTIVATE THE UNIT AGAIN, PRESS THE
ON/STANDBY BUTTON ON THE BACK PANEL TO SWITCH OFF THE UNIT. AFTER 10 SECONDS, PRESS THE ON/STANDBY BUTTON AGAIN TO SWITCH ON THE UNIT.
DIGITALIZING TURNTABLE INTO COMPUTER**

1. CONNECT THE PRODUCT TO A COMPUTER VIA THE USB CABLE
2. INSERT THE SOFTWARE CD AND FOLLOW THE ON-SCREEN INSTRUCTIONS.
3. USERS CAN FIND FURTHER INFORMATION ON THE SOFTWARE FUNCTIONS IN THE HELP MENU AND IN THE OPERATION INSTRUCTIONS OF

THE SOFTWARE. THERE ARE AVAILABLE AT THE FOLLOWING LINKS: http://www.audacity.com/
AUDACITY SOFTWARE OVERVIEW Audacity is free software, licensed under the GNU General Public License (GPL). More information, as well as open-source code, can be found on the web at https://www.audacityteam.org/download/

• Please ensure you have installed the software before starting. Setting up your PC to work with Audacity
  1. Connect an input source to the unit.
  2. Connect the USB lead to your computer.
  3. Install the Audacity recording software.
  4. Open the Audacity program.
  5. Select Preference from the Edit tab in the Audacity Menu. 6. Select the Audio I/O tab at the top left.

  • Under Playback, Device, select your internal sound card.
  • Under Recording, Device, select USB Audio CODEC.
  • Under Recording, Channels, select 2 (Stereo).
  • Check the box marked Play other tracks while recording a new one.
  • Check the box marked Software Playthrough.

Recording Albums with Audacity
1. Saving a project

• Audacity writes all the changed and recorded audio to a directory called Projectname_data, which is located right where you saved the project file itself.
• Thus, select Save Project from your Audacity File tab and choose a location and filename for your project.
• Please note that when you startup Audacity fresh, only the “Save As…” menu option is available.

2. How to record

• Set your USB turntable up to play the song or album you want to record.
• Click on the red Record button to beto begin recording.
• Lower tonearm on USB turntable onto album and track you want to record.
• Click on the blue Pause button to pause the recording. Press it again to continue.
• Click on the yellow Stop button.

That’s it. You can now play around with your recording and explore the editing capabilities of Audacity. Remember that you can use the Undo function almost without limits while the project is open.
NOTE: CDs cannot be burned directly from the Audacity application. Other CD-burning applications should be used.
POWER SAVING FEATURE:
TO SAVE ENERGY, IF THERE IS NO AUDIO SIGNAL FROM THE TURNTABLE OR BLUETOOTH FOR A PERIOD OF OVER AROUND 10 MINUTES, THEN THE UNIT WILL AUTOMATICALLY SWITCH TO OFF. IN ORDER TO RESTART THE UNIT IF NECESSARY, PLEASE SWITCH OFF AND SWITCH ON THE UNIT AGAIN BY PRESSING THE ON/STANDBY BUTTON AT THE BACK PANEL.

Specification

General

Model:
Dimensions:
Weight:
Power supply:
Power consumption:
Standard test condition:
Relative Humidity:| LBT-190
450(W) x 355(D) x 130(H)mm
4.5Kg
AC ADAPTER 100V-240V 50/60Hz 0.65A
3W
Ambient Temperature: 20 +/- 2 deg.C
65% +/- 5%
---|---

NOTE: Measurements can be carried out between 5 deg.C to 35 deg.C and 45% to 85% relative humidity.
Turntable Section:

Type:
Motor:
Driving Method:
Turntable Platter:
Speeds:
Wow and Flutter:
S/N Ratio:
Pitch Controls:
Starting Torque:
Braking System:
Starting Time:
Braking Time:
Time for Speed Change:
USB Function:
Computer interface:| 2-speed full manual
Miniature permanent magnet DC brushes
Belt drive
332mm (Aluminum)
33 and 45rpm
Less than 0.3% WRMS (JIS WTD) with 33 rpm
More than 50dB (DIN-B)
+/- 10%
N/A
Electronic brake
Less than 2 sec.
Less than 2 sec.
Less than 2 sec. from 33 to 45 rpm.
Less than 2 sec. from 33 to 45 rpm.
PC link (recording from turntable to computer by USB port)
USB 1.1 compliant 7/8/10 or MAC OSX
---|---

Tonearm section:

Type:
Effective Arm Length:
Overhang:
Tracking Error Angle:
Tracking Force Adjustment Range:
Cartridge MM Type:
Stylus pressure:
Cartridge weight:
Anti-skating Range:
Channel Separation:
Channel Balance:
Pre-Amplifier
Output:
RIAA (Frequency Response):| Static balanced S-shaped tone arm
200mm
10mm
Less than 3 degree
3-4g
Audio Technica AT-3600L
3.0±0.5g
2.5±0.5g
0~4g
More than 18 dB
Within 2.5dB at 1KHz
150mV +/-4dB (IN: 2.5mV 1KHz)
20Hz~20KHz +1/-3dB (IN: 1.5mV 1KHz)
---|---

Guarantee

Lenco offers service and warranty in accordance with European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer. Important note: It is not possible to send products that need repairs to Lenco directly. Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires. This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.
Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore some of the instructions, specifications, and pictures in this documentation may differ slightly from your particular situation. All items described in this guide are for illustration purposes only and may not apply to a particular situation. No legal rights or entitlements may be obtained from the description made in this manual.
Disposal of the Old Device
This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose of them in accordance with any applicable local laws of the requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in the treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).
CE Marking
Products with the CE marking comply with the EMC Directive (2014/30/EU) and the Low Voltage Directive (2014/35/EU) issued by the Commission of the European Community. Hereby, Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this product is in compliance with the essential requirements. The declaration of conformity may be consulted at techdoc@lenco.com
Service For more information and helpdesk support, please visit www.lenco.com
Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>