JONATHAN Y Silas 19 in. 3 Light Rustic Farmhouse Iron LED Pendant Installation Guide
- June 12, 2024
- JONATHAN Y
Table of Contents
JONATHAN Y Silas 19 in. 3 Light Rustic Farmhouse Iron LED Pendant
Product Information
The JYL1318A model is a lighting fixture that can be installed in homes and buildings. The product dimensions are 19W x 27-86H. The fixture comes with a mounting plate, suspension chain, canopy, bulb, light diffuser, washer, and cover. The lighting fixture requires assembly and installation by a licensed electrician. The external flexible cable or cord of the lamp cannot be replaced, and if it is damaged, the lamp should be destroyed. The product should be assembled on a soft surface to prevent scratching the finish during assembly.
Product Usage Instructions
Warning: Before installation, switch off the main electrical supply from
the main fuse box/circuit breaker. Inspect the item carefully before
attempting to install. If there is any damage or obvious defect, do not
install. The item may not be returned once it has been installed.
Care and Maintenance: Please make sure that you have all parts indicated
before you begin assembly of this item.
- Preparation: Before beginning assembly of the product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
- Tighten the loop (M) to the screw on the top of the fixture body (N).
- Install the mounting plate (B) to the junction box using mounting screws (C).
- Screw the collar loop (I) through the canopy (H) onto the nipple (F).
- Connect one end of the chain (K) to the loop (M) and the other end to the collar loop (I) with the quick link (J). Then back the collar loop ring (L) and the canopy (H) to the suspension chain.
- Pass the wires on the lamp body through the chain (K) collar loop (I) canopy (H) and connect the neutral line live wire on the lamp body with the neutral line live wire on the junction box.
- Fasten the canopy (H) to the junction box and collar loop ring (Lto the collar loop (I).
- Twist the bulb (O) onto the cap inside the fixture body (N).
- Twist the center rod (P) to the nut below the fixture body (N).
- Insert the center hole of the light diffuser (Q) and the center hole of the washer (R) into the center rod (P) and lock it with the nex nut (S).
- Insert the center hole of the cover (T) into the center rod (P) and lock the finial (U).
Wiring Instructions:
- Connect, Hot, Black or Red Outlet Supply Wire to: Black Parallel Cord (round & smooth) Clear, Brown, Gold or Black without Tracer (colored stripes) Insulated Wire (not green) with a copper metal conductor.
- Connect, Neutral, White Outlet Supply Wire to: White Parallel Cord (square & ridged) Clear, Brown, Gold or Black with Tracer (colored stripes) Insulated Wire (not green) with a Silver metal conductor.
Note: When parallel wire (SPT I & SPT II) is used, the neutral wire is square-shaped and ridged, and the hot wire will be round in shape and smooth.
Grounding Instructions:
- For installation in the United States: Wrap ground wire from the outlet box around green ground screw (E) on the mounting bracket, no less than 2 from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire connector.
- For installation in Canada: If the fixture is supplied with a ground wire, wrap the ground wire around the green grounding screw on the mounting bracket. Tighten the ground screw.
WARNING
- WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
- WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
- INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE
- To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
- To clean the inside of the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
- Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE & IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item.
- This item should be assembled on a soft surface to prevent scratching the finish during assembly.
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation.
- The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed.
Part List and Hardware List
PREPARATION
- Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
- Estimated Assembly Time: 20 minutes
INSTALLATION STEPS
- Tighten the loop (M) to the screw on the top of the fixture body (N).
- Install the mounting plate (B) to the junction box using mounting screws (C).
- Screw the collar loop (I) through the canopy (H) onto the nipple (F).
- Connect one end of the chain (K) to the loop (M) and the other end to the collar loop (I) with the quick link (J). Then back the collar loop ring (L) and the canopy (H) to the suspension chain.
- Pass the wires on the lamp body through the chain (K) collar loop (I) canopy (H) and connect the neutral line live wire on the lamp body with the neutral line live wire on the junction box.
- Fasten the canopy (H) to the junction box and the collar loop ring (L）to the collar loop (I).
- Twist the bulb (O) onto the cap inside the fixture body (N).
- Twist the center rod (P) to the nut below the fixture body (N).
- Insert the center hole of the light diffuser (Q) and the center hole of the washer (R) into the center rod (P) and lock it with the nex nut (S).
- Insert the center hole of the cover (T) into the center rod (P) and lock the finial (U).
Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White
Outlet Supply Wire to:
---|---
Black| White
- Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)| Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor| Insulated Wire (not green) with Silver metal conductor.
Note : When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions:
- For installation in the United States: Wrap ground wire from the outlet box around green ground screw(E) on the mounting bracket, no less than 2″ from wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
- For installation in Canada: If the fixture is supplied with ground wire, wrap the ground wire around the green grounding screw on the mounting bracket. Tighten the ground screw.
PLEASE USE TYPE”A” BULB MAX 40-WATT OR LED BULB MAX 9-WATT, THERE ARE 3PCS LED
9-WATT BULBS IN THE BOX.
ENJOY YOUR LAMP
Model#: JYL1318A
Product Dimensions :19″Wx27″-86″H
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>