JONATHAN Y JYL9930 8 Chic Boho Chandeliers and Pendant Lights Instruction Manual
- October 30, 2023
- JONATHAN Y
Table of Contents
Model#: JYL9930
Product Dimensions: Ø12.5”X19”H
Instruction Manual
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED
ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE
BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN
INSTALLED.
CARE AND MAINTENANCE
To clean the outside of the fixture, use a dry or slightly dampened clean
cloth (use clean water, never a solvent) to wipe the surface of the fixture.
To clean the inside of the fixture, first disconnect power to the fixture by
turning off the circuit breaker or by removing the fuse at the fuse box. Next,
use a dry or slightly dampened clean cloth (use clean water, never a solvent)
to wipe the interior surface of the fixture.
Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a
dry soft cloth to dust or wipe carefully.
NOTICE & IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
- The external flexible cable or cord of this luminaire cannot be replaced If the cord is damaged, the luminaire shall be destroyed
PIECE| DESCRIPTION| PICTURE| QUANTITY| PIECE|
DESCRIPTION| PICTURE| QUANTITY
---|---|---|---|---|---|---|---
A| Mounting Plate| | 1X| H| Mounting Screw| | 2X
B| Canopy| | I X| 1| Wire Nut| | 3X
C| Hanging Loop| | I X| J| Lamp Body| | 1X
D| Canopy Nut| | I X| K| Loop| | lx
E| Chain| | 1X| L| Lamp Shade| | lx
F| Closable Link I cap| | 2X| M| bulb| | 1X
G| Nut| | 3X| | | |
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is
missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
- Fix the Mounting Plate(A) to the junction box with Mounting Screw (H).
- Carefully remove the Lamp Body (J) from the Lamp Shade (L) by turning the Nut (G) counter clockwise
- Turn clockwise to fix the lifting Loop (K) to the Lamp Body (J),
- Chain (E) Through special Canopy (B) and Canopy Nut (D), Closable Link (F) is used to connect one end of Chain (E) to the Hanging Loop (C) and the other end to the Loop (K).
- Connect the main line and ground wire on the lamp body with the main line and ground wire in the junction box with the Wire Nut ( I )
Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
---|---
Black| White
- Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)| Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor| Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is
square shaped and ridged and the hot wire will be round in shape and smooth. (
See Illustration on left. )
Grounding Instructions:
a) For installation in the United States: Wrap ground wire from outlet box
around green ground screw on mounting bracket, no less than 2″ from wire end.
Tighten ground screw. If fixture is supplied with a ground wire, connect to
outlet ground wire with a wire connector.
b) For installation in Canada: If fixture is supplied with ground wire, wrap
ground wire around green grounding screw on mounting bracket. Tighten ground
screw.
- Push the Canopy(B) up to the ceiling and turn the Canopy Nut (D) clockwise to secure it
- Insert the bulb (M) into the Sockets. Be sure to use light bulb(M) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulb.
- Carefully place the Lamp Body (J) into the Lamp Shade (L) and turn the Nut (G) clockwise to secure it
PLEASUE USE TYPE”A” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED MAX 9-WATT
THERE ARE 1 X 4W LED BULBS IN THE BOX.
ENJOY YOUR LAMP
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>