Chargers ET-BOX01 Two In One Wireless Charger and Catchall Tray Instruction Manual
- June 4, 2024
- Chargers
Table of Contents
User guide for
Wireless charger
The Wireless charger is a two-in-one wireless charger and catchall tray, designed to hold the daily essentials and discreetly power your device. It is functional and easy-to-use, supporting all electronic devices with Qi compatibility. The Wireless charger is inspired by industrial design and has a streamlined aesthetic and leather finish. Station it in your home office or on a bedside table.
Instructions for use
How to connect
1. Connect the Type-C cable to the port on your Wireless charger.
2. Plug the other end of the Type-C cable into a power adapter or
computer outlet with the correct output: 5V/2A(MAX), 9V/1.67A(MAX),
12V/2A(MAX). Slow white LED flashes indicate that standby mode is activated.
3. Place your Qi-compatible device onto the centre of the wireless
charging area. A solid white light indicates that the device is charging. If
the device does not begin to charge immediately, carefully move it around
until the desired alignment is achieved.
4. When the device is fully charged, the LED light will turn off.
Alignment
Wireless Qi technology is activated when the transmitter coil in The Wireless charger and the receiver coil in your device are aligned.
The Wireless charger’s transmitter coil is located in the centre of the raised section. To begin charging, place your device here.
You can check if your device is positioned correctly by monitoring the LED light. Charging mode is indicated by a solid white light.
If charging mode is not activated, carefully reposition your device until the two coils are aligned.
Safety information
– Plug the product into a reliable and correct electrical outlet.
– Do not place credit cards or metallic items, such as keys, on the raised
side of The Wireless charger.
– Do not place mechanical watches on the raised side of The Charging Catchall.
The magnetic field created by the coils can damage them.
– The Wireless charger should be kept in a dry and ventilated environment. Do
not use it in severely hot or humid conditions. It is for indoor use only.
– Do not attempt to disassemble the product.
– If the USB-C cable or transmitter plate begins to overheat, disconnect from
power. Only attempt to use it again when it has cooled down.
– Do not exceed the maximum input voltage of 12V/2A. Supplying a voltage over
the maximum rating can damage The Wireless charger and cause safety hazards.
Device not charging
– Make sure the device is Qi-enabled.
– Make sure The Wireless charger is connected to a working power outlet.
– Make sure the device is aligned correctly.
– Ensure there are no other items resting on the charging section.
– Remove the device’s case. It may be preventing charging.
LED indicator status
| Slow white flashes | Standby mode |
|---|---|
| Solid white | Charging mode |
(when it’s fully charged it will turn off)
Fast white flashes| Foreign object detected
Technical specifications
| Input | 5V/2A, 9V/2A, 12V/1.5A |
|---|---|
| Output | 5W/7.5W/10W/15W |
| Dimension | 27 x 20 x 0.5 (cm) |
| Weight | 0.5kg |
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is Subject To
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Changes or modifications not explicitly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
Note: this equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and candidate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communica-tions.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>