BEGA 51284.6K3 System Pendant Luminaire Instruction Manual

BEGA 51284.6K3 System Pendant Luminaire

DIMENSION

Application

• Pendant luminaire · Indoor luminaire for unshielded and uniform light, with synthetic cover, translucent white and with metal housing.
• BEGA System pendant luminaire for use in combination with various modular BEGA installation components.

Product description

• Metal housing, finish colour matt copper Synthetic cover, translucent white

• Black flex suspension 2 x 0,5@ with 1 steel messenger wire

• Overall length of luminaire approx. 2000 mm Safety class III 3

• c  – Conformity mark

• Weight: 1.7 kg
  This product contains light sources of energy efficiency class(es) D

• Luminaire without canopy,

• for connection to an additional required BEGA Installation component (accessory)

SPECIFICATION

• Lamp
  • Module connected wattage 23.2 W
  • Luminaire connected wattage 26.4 W
  • Rated temperature ta = 25 °C
  • Ambient temperature ta max = 45 °C
• 51 284.6 K3
  • Module designation LED -1419/930
  • Colour temperature 3000 K
  • Colour rendering index CRI > 90
  • Module luminous flux 3600 lm
  • Luminaire luminous flux 3305 lm
  • Luminaire luminous efficiency 125,2 lm / W

Safety

• The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.

• The manufacturer accepts no liability for damage caused by improper use or installation.

• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
  Please note:

  • The luminaire can only be operated with an operating device that fulfills the requirements according to EN 61347-2-13.
  • The maximum idle voltage of 60 V DC must conform to SELV or SELV equivalent.

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• To operate this luminaire one of the following additional BEGA Installation components must be ordered – accessoire.
• Please refer to the instructions for use for the BEGA installation component selected for luminaire installation
  Please note:
  The manufacturer accepts no liability for damage caused by improper use or installation if no BEGA installation component is used to install this BEGA system pendant luminaire.

Replacing the LED module

• The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.

• It is also listed in the spare parts overview at the end of these instructions for use.

• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified person using commercially available tools.

• Disconnect the system from the power supply.

• Loosen canopy / canopy cover and push it downward on the luminaire cable.

• Remove the connecting wires of the luminaire cable inside the canopy and unhook the hanger of the pendant luminaire from the mounting plate / installation frame.

• Unfasten the steel wire of the luminaire cable.

• Remove the strain reliever from the luminaire hanger.

• Loosen the knurled nut and remove the strain reliever via the luminaire cable.

• Remove the canopy / canopy cover.

• Undo the knob in the funnel-shaped upper part of the housing by turning anti-clockwise.

• Remove the knob and upper part of the housing via the luminaire cable.

• Detach the synthetic cover and remove via the luminaire cable.

• Loosen the outer 2 Torx screws (T 10) of the housing tube.

• Remove the connecting wires of the LED module strip from the terminals and remove the housing tube complete with LED module (module strip) via the luminaire cable.

• Guide the replacement LED module (housing tube with module strip) over the luminaire cable.

• Fasten the housing tube with LED module strip onto the luminaire base using 2 Torx screws (T 10).

• Connect the connecting wires of the module strip to terminals.

• Please follow the installation instructions for the new LED module.

• Guide the synthetic cover over the luminaire cable onto the luminaire base.

• A defective luminaire cover must be replaced.

• Guide the funnel-shaped upper part of the housing and knob over the luminaire cable onto the synthetic cover and tighten the knob in clockwise direction.
  IMPORTANT: The luminaire cable must first be guided through the bore hole on the underside of the canopy.

• Install the strain reliever back onto the luminaire cable and clip the strain reliever into the luminaire hanger.

• Refasten the steel wire of the luminaire cable.

• Hook the hanger of the pendant luminaire in the mounting plate / installation frame and reconnect the wires of the luminaire cable in the canopy.

• Attach the canopy / canopy cover to the ceiling.

Fine adjustment of the pendant luminaire

• Undo the knob in the funnel-shaped upper part of the housing by turning it anti-clockwise to enable the fine adjustment of the pendant luminaire along its horizontal axis.
• Hold the bottom edge of the pendant luminaire with one hand and simultaneously turn the synthetic cover along its vertical axis with the other hand until the luminaire body is aligned horizontally.
• Tighten the knob in the funnel-shaped upper part of the housing by turning it in clockwise direction.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Accessories

BEGA Installation components with LED power supply unit.
Satin black finish
Depending on the desired type of installation, the following suitable installation components are available for this BEGA system pendant luminaire:

• For all level ceilings:
  • 13 328 Surface-mounted canopy (Type A) DALI · 220-240 V · 700 mA DC
  • 13 330 Surface-mounted canopy (Type AS) Smart controllable / dimmable · 220-240 V · 700 mA DC
• Suitable for level ceilings and sloped ceilings with a pitch of 0 – 40°:
  • 13 332 Surface-mounted canopy (Type B) DALI · 220-240 V · 700 mA DC
  • 13 334 Recessed canopy (Type C) DALI · 220-240 V · 700 mA DC
  • 13 336 Recessed canopy (Type CS) Smart controllable / dimmable · 220-240 V · 700 mA DC

Spares

• LED module 3000 K LED -1419/930
• Synthetic cover 75 005 972

ABOUT COMPANY

• BEGA Gantenbrink-Leuchten KG
• Postfach 3160
• 58689 Menden
• info@bega.com
• www.bega.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>