R G Racing CB650F Radiator Guard Instructions
- June 16, 2024
- R G Racing
Table of Contents
RAD0295PRO
FITTING INSTRUCTIONS
FOR RAD0295PRO
CB650F Radiator Guard
THIS KIT CONTAINS
THE ITEMS PICTURED AND LABELLED OVER PAGE.
SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE
FITTED BY A QUALIFIED TECHNICIAN.
PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE
WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS, THESE
RUBBER WASHERS CAN BE THROWN AWAY.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
| TOOLS REQUIRED | GENERAL TORQUE SETTINGS |
|---|
• SOCKET SET
• FLAT HEAD SCREWDRIVER| M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm
LEGEND
| ITEM NO. | DESCRIPTION | QTY |
|---|---|---|
| ITEM 1 | RAD0295PRO (RADIATOR GUARD) | 1 |
| ITEM 2 | RB0015 (RUBBER GROMMETS) | 6 |
| ITEM 3 | CABLE TIES | 2 |
FITTING DIAGRAM
FITTING INSTRUCTIONS
- Insert the 4x rubber grommets into the radiator guard in the holes circled in yellow (as shown above) if they do not come already installed.
- If any bodywork needs to be removed refer to your service manual.
- Remove the upper and lower radiator fastening bolts (offer the radiator guard into position to show which bolts need to be removed.)
- Slide the R&G Radiator Guard into position.
- Replace the bolts to fix the guard into position.
- Use one of the cable ties through the slots to secure the radiator into position as shown in picture 3.
- Check all components are secure and all bolts are tight before riding.
See more R &G products for your Motorcycle in the links below:
R&G Racing | Cleaning/Lubrication – Gleam range for All Vehicles (rg-
racing.com)
ISSUE 1 – 17/03/2023 (DM)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad
indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state
shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products
other than those in R&G’s order or confirmation and the Buyer confirms it has
chosen the Products as being of merchantable quality and suitable for its
particular purposes. Where R&G fits the Products or undertakes other services
it shall exercise reasonable skill and care and rectify any fault free of
charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of
the Products. On return of any defective Products R&G shall at its option
either supply a replacement or refund the purchase money but shall not be
liable if the Products have been modified or used or maintained otherwise than
in accordance with R&G’s or manufacturer’s instructions and good engineering
practice or if the defect arises from accident or neglect. Other than
identified above and subject to R&G not limiting its liability for causing
death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts
paid by the Buyer for the Products or the fitting or service concerned. These
terms do not affect the Buyer’s statutory rights.
R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be
rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to
original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of
the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued
products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
R&G Racing
Unit 1, Shelley’s Lane, East Worldham,
Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com Email: info@rg-
racing.com
References
- RACING.COM - YOUR RACING CONNECTION
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>