BEGA 85 026 Light Building Element Head Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 85 026 Light Building Element Head
Application
Product description
Dark Sky
Overvoltage protection
Safety
Installation
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 85 026 Light Building Element Head

BEGA-85-026-Light-Building-Element-Head-PRODUCT

Specifications

Material: Cast aluminium, aluminium, stainless steel

Usage Instructions

A light building element tube is required for installation of the light building element head (must be ordered separately).
Ensure the installation and commissioning are carried out by a qualified electrician following national safety regulations.
Protect the luminaire against overvoltage and consider additional protection components for transient events.
Temperature-sensitive components are protected by temporary thermal regulation within the luminaire.
No light is emitted into the upper half-space of the luminaire.

FAQ
Q: Is the luminaire suitable for outdoor use?
A: Yes, the luminaire has an IP 65 protection class making itsuitable for outdoor use as it is dust-tight and protected against water jets.

Light building element head

$BEGA-85-026-Light-Building-Element-Head-PRODUCT $2$$ Instructions for use

Application

Light building element head with shielded light for illuminating and designing squares, driveways and entrance areas.
Light exit 360°. The light is deflected by means of a conical reflector onto the surface to be illuminated.
A light building element tube is required for the installation of the light building element head, which must be ordered separately (see accessories).

Product description

Luminaire made of cast aluminium, aluminium and stainless steel
BEGA Unidure® coating technology
Clear synthetic cover with optical structure Silicone gasket
Reflector surface made of pure aluminium Connecting cable X05BQ-F 5 G 1 mm²
Cable length 5,5 m
BEGA Ultimate Driver®
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1 LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI controllable
Number of DALI addresses: 1
A basic isolation exists between power cable and control line
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK04
Protection against mechanical
impacts < 0.5 joule
Conformity mark
Horizontal wind catching area: 0.063 m² Weight: 8.8 kg
This product contains light sources of energy efficiency class(es) C, D

Dark Sky

The light of this luminaire is directed evenly and highly efficiently onto the surface to be illuminated. No light is emitted into the upper half-space of the luminaire.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage 40 W
Luminaire connected wattage 44.5 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 35 °C

85 026 K3

Module designation 4x LED-1317/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 6600 lm
Luminaire luminous flux 4936 lm
Luminaire luminous efficiency 110,9 lm / W

85 026 K4

Module designation 4x LED-1317/840
Colour temperature 4000 K
Colour rendering index CRI > 80
Module luminous flux 6960 lm
Luminaire luminous flux 5205 lm
Luminaire luminous efficiency 117 lm / W

Installation

Thread the connection cable into the light building element tube. Align the light building element head and secure it in place.
Tighten the lateral hexagon socket screws (wrench size 5 mm).

Torque = 16 Nm
Open the connection box.
Lead the luminaire wiring and mains supply cable through the cable entry into the connection box.
Note correct configuration of the mains supply cable.
Make mains supply connection at the brown (L), blue (N) and green-yellow lead ).
The connection of the control cables is achieved by means of the both leads marked with DALI.
In case these leads are not used the luminaire will be operated at full light output.
Close the connection box.

Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.

Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective synthetic diffuser must be replaced. Close the luminaire.

Accessories

The light building element head can be combined with the following light building element tubes:
Cylindrical aluminium poles, lacquered with access door and connection box 71 084

84 720 with anchorage.section H 4300 mm
84 721 with base plate H 4300 mm
Cylindrical aluminium poles, lacquered with access door, connection box 71 084 and built-in adjustable floodlight
84 722 with anchorage unit H 4300 mm
84 723 with base plate H 4300 mm

Cylindrical aluminium poles, lacquered with access door, connection box 71 084 and 2 built-in adjustable floodlights

84 724 with anchorage unit H 4300 mm
84 725 with base plate H 4300 mm
Cylindrical poles made of laminated wood in accordance with DIN EN 14080 and aluminium, with access door and connection box 71 084
84 730 with anchorage unit H 4300 mm
84 731 with base plate H 4300 mm
71 219 Anchorage unit for light building element tube with base plate

For the accessories a separate instructions for use can be provided upon request.

Spares