BEGA 50 019 Ceiling and Wall Luminaire For Indoor Use Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 50 019 Ceiling and Wall Luminaire For Indoor Use
Instructions for use
Product Description
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50 019 Ceiling and Wall Luminaire For Indoor Use

BEGA-50 019-Ceiling-and-Wall-Luminaire-For-Indoor-Use-
product

Instructions for use

$BEGA-50 019-Ceiling-and-Wall-Luminaire-For-Indoor-Use-fig- $1$$

Application

Ceiling and wall luminaire
indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks.
They are ideal for places where soft and uniform lighting distribution is required.
Luminaire with HF-motion sensor.

Product Description

Metal housing, finish colour white
Hand-blown opal glass, satin matt, with bayonet closure
Integrated HF-motion sensor,
maximum range 8 m
2 mounting holes ø 6mm
Distance apart 340mm
2 cable entries for through-wiring for mains
cable up to ø 10.5 mm max. 3 × 1.5
Connection terminal 2.5
Earth conductor connection
Complies with flicker requirements by IEEE 1789, DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
230 V y 50 Hz
BEGA Thermal Switch
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Impact strength IK06
Protection against mechanical
impacts < 1 joule
Conformity mark
Weight: 4.4 kg
This product contains light sources of energy efficiency class(es) D, E

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage 27.6 W
Luminaire connected wattage 33 W
Rated temperature ta=25 °C
Ambient temperature ta max=30 °C

50 019K27

Colour temperature 2700 K
Colour rendering index CRI >90
Module luminous flux 4165 lm
Luminaire luminous flux 2294 lm
Luminaire luminous efficiency 69,5 lm/W

50 019K3

Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 4305 lm
Luminaire luminous flux 2372 lm
Luminaire luminous efficiency 71,9 lm/W

50 019K4

Colour temperature 4000 K
Colour rendering index CRI >90
Module luminous flux 4480 lm
Luminaire luminous flux 2468 lm
Luminaire luminous efficiency 74,8 lm/W

Luminaire with trim ring
Before installing it onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Pass the main supply cable through the grommet into the luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material onto the mounting surface.
It is imperative to use the enclosed gaskets.
Dismantle the mains supply cable approx. 60 mm.
Pull silicone sleeves over the wires and make earth and electrical connections to the terminals.
Place glass in the luminaire housing and observe that the cam pins fit into the notches of the glass.
Screw in the glass by turning it clockwise.
Thus, you reach a safe and vibration-resistant holding of the glass.
To release the glass from the luminaire housing, turn it counterclockwise. $BEGA-50 019-Ceiling-and-Wall-Luminaire-For-Indoor-Use-fig- $2$$

The built-in motion sensor operates at a frequency of 5.8 GHz. By moving within the detection range the motion sensor switches on the LED module inside the luminaire with a defined dwell time – push-button “Dwell time”. With a wall mounting height of 1.8 m or a ceiling mounting height of 2.6 m, the maximum range is 8 meters (see sketch).

$BEGA-50 019-Ceiling-and-Wall-Luminaire-For-Indoor-Use-fig- $3$$ The max. wall mounting height is 2.7 m and the max. ceiling mounting height is 4.0 m, in which the range reduces significantly. The range can be set individually – push-button
“Sensitivity”. It should be noted that metal parts that are mounted near the luminaire can affect the range.

With the three integrated push-buttons
(Brightness, Dwell time and Sensitivity) on the motion sensor, specific settings can be made. The first keypress activates the setting function. Press a push-button to switch each function to the next level, and the LED indicator on the motion sensor flashes to confirm. After reaching the highest level, the level-setting begins with “Level 1”.

$BEGA-50 019-Ceiling-and-Wall-Luminaire-For-Indoor-Use-fig- $4$$ $BEGA-50 019-Ceiling-and-Wall- Luminaire-For-Indoor-Use-fig- $5$$ $BEGA-50 019-Ceiling-and-Wall-Luminaire-For-Indoor-Use-fig- $6$$

The integrated motion sensor can be set individually with the brightness levels on the ambient brightness – Press the button “Brightness”. Further individual illumination levels can be used with the button “Brightness” and set with the “learning mode”. Press the button “brightness” (> 3 s) to enable the “learning mode”. There is a slow flashing of the LED indicator. After about two minutes, the current brightness value is measured for one minute, the LED flashes faster. After completion, the measured brightness value is saved and is available in stage 6 of “Brightness” is the new brightness value. To simplify the initial operation, the settings have been made as follows:

Range = 75% (6 m)
Dwell time = 10 s
Light sensor = daylight

Factory Reset
The motion sensor can be reset to the factory settings (MICAS) by simultaneously pressing the buttons “Sensitivity” and “Dwell time” for about 5 s.
The factory settings are as follows:

Range = 75% (6 m)
Dwell time = 900 s
Light sensor = daylight

Test mode

The test mode can be used to check the change of settings of the motion sensor.
Press the button “Sensitivity” (> 3 s) to enable the “test mode”.
Each further keystroke of this push-button prolongs the test mode.
The active test mode is displayed by a flashing of the LED indicator (2 s interval).
After 3 minutes the test mode is automatically disabled.

Replacement of the LED unit

The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to those of the
LED units were originally fitted. The LED unit can be replaced by qualified persons using standard tools.
Disconnect from the main supply.
Unscrew the glass from the luminaire housing by turning it counterclockwise.
Replace the LED unit.
Screw in the glass by turning it clockwise.
The defective glass must be replaced.

Accessory · Trim rings
For this luminaire metal trim rings in 3 enamel surfaces are optionally available.
Trim rings are accessories and must be ordered separately.