BEGA 33062 Recessed Wall Luminaire Instruction Manual

Table of Contents

BEGA-33062-Recessed-Wall-Luminaire-Product

Specifications:

Installation:

Ensure to follow national safety regulations during installation.
Installation and commissioning should only be done by a qualified electrician.
Use bounce-free switching contacts for optimal protection of electronic components.

Maintenance:
Use chemical cleaning agents cautiously around the luminaire if coated with BEGA Tricoatb to avoid damage to the coating.

FAQ:

Q: Can this luminaire be used for surface mounting?
A: Yes, this luminaire can be used for flush or surface mounting installations.
Q: What is the recommended power supply for this luminaire?
A: The recommended LED power supply unit is rated at 220-240 V x 0/50-60 Hz DC 176-276 V.

Recessed wall luminaire with asymmetrical flat beam light distribution, for flush or surface mounting installation.
For the wide beam and uniform illumination of surfaces and paths.

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Tricoat® coating technology
Colour graphite or silver
Safety glass with optical structure
Silicone gasket
Reflector made of pure anodised aluminium
Fixing is achieved by using two adjustable wedge-shaped claws
Required recessed opening 315 x 110 mm
Recessed depth 90 mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@
Connecting terminal and earth conductor terminal 2.5@
BEGA Ultimate Driver®
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-276 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK08
Protection against mechanical impacts < 5 joule
– Safety mark
– Conformity mark
Weight: 2.0 kg
This product contains light sources of energy efficiency class(es) C

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71 320.

Please note:

This luminaire is coated with BEGA Tricoatb.
BEGA Tricoatb is a registered trademark for a technology that we use to achieve optimal corrosion resistance.
Even the best possible surface protection and the highest corrosion resistance can be rendered almost ineffective in some cases by aggressive media caused by the leaching of building materials.
Where such media are suspected, a material analysis must be carried out before installation.
Always avoid excessive use of chemical cleaning agents in the vicinity of the luminaire.

The recessed opening will be covered by the frame of the luminaire housing.
Fixing of the luminaire is achieved by using two adjustable wedge-shaped claws.
Installation in solid, plastered walls:
The installation housing 10 436 is available for this purpose. If this is not used, an exact recessed opening of 315 x 110 mm with a minimum depth of 90 mm is required.
Installation in exposed brickwork:
The construction of an on-site recessed opening with the exact installation dimensions of 315 x 110 mm with a minimum depth of 90 mm is required. An installation housing cannot be used.
Installation in drywalling:
A recessed opening of 315 x 110 mm with a minimum depth of 90 mm is required. The claws grip behind drywall.
Installation into insulated façades:
For installation in EWIS external wall insulation systems please use installation housing 13 522 in combination with a plaster frame 10 036 or 13

Open luminaire:

Undo the screws and remove the housing cover.
Disconnect the plug-connection of the LED connecting cable.
Disconnect the earth conductor connection from the plug connection.
Lead the main supply cable through the cable entry into the luminaire housing.
Make the earth conductor connection and the electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
To guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Connect the LED connection cable using a plug connector.
Put on earth conductor connection of the housing cover. Assemble the housing cover.
Make sure that the gasket is positioned correctly.
Tighten the screws evenly.
Insert luminaire housing into the recessed opening. Hand-tighten the screws of the claw fastener evenly. Do not use an electric screwdriver!

$BEGA-33062-Recessed-Wall-Luminaire-Fig- $1$$

33 062 K3

33 062 K4

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Close the luminaire.