BEGA 50 018 P Ceiling and Wall Luminaire For Indoor Use Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

Instructions for use
Product description
Safety
Overvoltage protection
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50 018 P Ceiling and Wall Luminaire For Indoor Use Instruction Manual

Ceiling and wall luminaire for indoor use

Dimensions Ceiling

Instructions for use

Application
Ceiling and wall luminaire · indoor luminaire made of impact resistant synthetic diffuser and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.

Product description

Metal housing, finish colour white
Impact resistant synthetic diffuser, white, with bayonet closure
2 mounting holes ø 6mm
Distance apart 340mm
2 cable entries for through-wiring for mains
cable up to ø 10,5 mm max. 5 x 1.5@
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Safety mark
Conformity mark
Weight: 3.0 kg
This product contains light sources of energy efficiency class(es) D, E

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage: 42.6 W
Luminaire connected wattage: 47.4 W
Rated temperature: ta=25 °C
Ambient temperature ta: max=40 °C

50 018 PK27

Colour temperature: 2700 K
Colour rendering index: CRI >90
Module luminous flux: 6225 lm
Luminaire luminous flux: 4691 lm
Luminaire luminous efficiency: 99 lm/W

50 018 PK3

Colour temperature: 3000 K
Colour rendering index: CRI >90
Module luminous flux: 6435 lm
Luminaire luminous flux: 4850 lm
Luminaire luminous efficiency: 102,3 lm/W

50 018 PK4

Colour temperature: 4000 K
Colour rendering index: CRI >90
Module luminous flux: 6695 lm
Luminaire luminous flux: 5045 lm
Luminaire luminous efficiency: 106,4 lm/W

Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Pass the mains supply cable through the grommet into luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material on to the mounting surface.
It is imperative to use the enclosed gaskets.
Dismantle the mains supply cable approx. 60 mm.
Make earth and electrical connection to the terminals.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Place the synthetic diffuser to the luminaire housing and observe that the cam pins fit into the notches of the synthetic diffuser.
Screw in synthetic diffuser by turning it clockwise.
Thus, you reach a safe and vibrationresistant holding of the synthetic diffuser.

To release the synthetic diffuser from the luminaire housing, turn it counter- clockwise.

Replacement of the LED unit

The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to those of the LED units originally fitted. The LED unit can be replaced by qualified persons using standard tools.
Disconnect from main supply.
Unscrew synthetic diffuser from luminaire housing by turning it counter- clockwise.
Disassemble LED unit.
Assemble LED replacement unit.
Note installation instructions of the LED unit.
Screw in synthetic diffuser by turning it clockwise.
A damaged synthetic diffuser must be replaced.

Accessory · Trim rings

For this luminaire metal trim rings in 3 enamel surfaces are optional available.
Trim rings are accessories and must be ordered separately.

Item: Part. No