BEGA 34021.1K4 Ceiling Luminaire For Indoor Instruction Manual

Table of Contents

Specifications:
- Material: Opal glass, satin matt
- Finish: White Silicone gasket
- Distance apart: 144 mm
- Weight: 1.6 kg
- LED power supply unit: 220-240 V x 0/50-60 Hz DC 176-280 V DC Start 190 V
- DALI-controllable with 1 address
- Basic insulation between mains and control cables
- Luminaire protection for temperature-sensitive components
- Energy efficiency class: D

Safety Information:
- The installation and operation of this luminaire must comply with national safety regulations.
- Only a qualified electrician should carry out installation and commissioning to prevent any damage due to improper use or installation.
- Any modifications should be done by authorized personnel to avoid liability issues.
Overvoltage Protection:
- The luminaire’s electronic components are protected against overvoltage by DIN EN 61547 standards. For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website.
Product Components:
- The luminaire consists of opal glass with a satin matt finish and a silicone gasket.
- It features an LED power supply unit with DALI control capability and basic insulation for safety.
- The distance between the connecting terminals is 144 mm, ensuring proper installation.
Installation Instructions:
- Ensure the power supply is switched off before installation.
- Mount the luminaire securely at the desired location using appropriate fixtures.
- Connect the mains and control cables as per the provided guidelines, ensuring proper insulation.
- Commission the luminaire by following the manufacturer’s instructions for the DALI control setup.

Q: What is the weight of the luminaire?
- A: The weight of the luminaire is 1.6 kg.
Q: Is the luminaire suitable for outdoor use?
- A: The product is not specified for outdoor use; it is recommended for indoor applications only.
Q: Can the luminaire be dimmed?
- A: Yes, the luminaire is DALI-controllable, allowing for dimming functionality based on the DALI address provided.

Ceiling luminaire for indoor use

$BEGA-34021-1K4-Ceiling-Luminaire-For-Indoor-FIG-1 $1$$

Application

Ceiling-mounted luminaire indoor luminaire with handblown opal glass, satin matt and aluminium housing, for all lighting tasks in interior applications.
They are ideal for places where a soft and uniform lighting distribution is required.

Luminaire made of Aluminium, finish colour white
Opal glass, satin matt, with screw neck Silicone gasket
2 mounting holes ø 5.5mm Distance apart 144mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5mm, max. 5G1.5@
Connecting terminal and earth conductor terminal 2.5@
2-pole connecting terminal for digital control
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-280 V
DC Start ≥ 190 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
- $BEGA-34021-1K4-Ceiling-Luminaire-For-Indoor-FIG-1 $2$$ – Safety mark
- – Conformity mark
Weight: 1.6 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

34 021.1K3

34 021.1K4

LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Remove glass from luminaire housing by turning it counterclockwise.
Undo knurled screws and remove the cover plate. Lead the main supply cable through the cable entry into the luminaire housing.
Fasten the luminaire housing with the supplied fastening material or other suitable fastening material to the mounting surface.
It is essential to use the enclosed protection against accidental contact.
Establish an earth conductor connection and make the electrical connection to the terminals.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Make an earth conductor connection between the cover plate and luminaire housing.
Assemble the cover plate.
Screw glass with gasket into luminaire housing.
Make sure that the gasket is positioned correctly

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced. Close the luminaire.

Spares