BEGA 50018K27 Ceiling and wall luminaire for indoor use Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 50018K27 Ceiling and wall luminaire for indoor use
Dimension
Ceiling and wall luminaire for indoor use
Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass
and metal housing, for all lighting tasks. They are ideal for places where a
soft and uniform lighting distribution is required.
Product Description
Metal housing, finish colour white
Hand-blown opal glass, satin matt, with bayonet closure
2 mounting holes ø 6 mm
Distance apart 340 mm
2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x
1.5@
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Impact strength IK06
Protection against mechanical
impacts < 1 joule r
– Safety mark c
– Conformity mark
Weight: 4.2 kg
This product contains light sources of energy efficiency class(es) D, E
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer
Overvoltage Protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
Module connected wattage 42.6 W
Luminaire connected wattage 47.4 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C
50 018 K27
Colour temperature 2700 K
Colour rendering index CRI > 90
Module luminous flux 6225 lm
Luminaire luminous flux 3581 lm
Luminaire luminous efficiency 75,5 lm / W
50 018 K3
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 6435 lm
Luminaire luminous flux 3703 lm
Luminaire luminous efficiency 78,1 lm / W
50 018 K4
Colour temperature 4000 K
Colour rendering index CRI > 90
Module luminous flux 6695 lm
Luminaire luminous flux 3853 lm
Luminaire luminous efficiency 81,3 lm / W
Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be
inserted into the trim ring (accessory).
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or revamping.
Pass the mains supply cable through the grommet into luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material on
to the mounting surface.
It is imperative to use the enclosed gaskets.
Dismantle the mains supply cable approx. 60 mm.
Make earth and electrical connection to the terminals.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light
output.
Place glass to the luminaire housing and observe that the cam pins fit into
the notches of the glass.
Screw in glass by turning it clockwise. Thus, you reach a safe and vibration-
resistant holding of the glass.
To release the glass from the luminaire housing turn it counter-clockwise.
Replacement of the LED unit
The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to
those of the
LED units originally fitted. The LED unit can be replaced by qualified persons
using standard tools.
Disconnect from main supply.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Replace the LED unit.
Screw in glass by turning it clockwise.
Defective glass must be replaced.
Accessory · Trim rings
For this luminaire metal trim rings in 3 enamel surfaces are optional
available.
Trim rings are accessories and must be ordered separately.
Item Part. No
Colour white 13 007
Colour palladium 13 008
Colour glossy silver 13 009
Spares
Spare glass 11 003 323 .0R G
LED unit 2700 K 75 005 486 K27
LED unit 3000 K 75 005 486 K3
LED unit 4000 K 75 005 486 K4
Customer Support
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden ·info@bega.com · www.bega.com 3 / 3
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>