BEGA 23296K4 Ceiling and wall luminaire for indoor use Instruction Manual

Table of Contents

Specifications:
- Product Description: Metal housing, finish colour white, Hand-blown opal glass with sliding-bolt closure
- Distance Apart: 155mm
- Weight: 2.2 kg
- LED network: 220-240 V x 0/50-60 Hz DC 170-280 V
- Safety Class: I
- Impact Strength: IK06
- Contains light sources of energy efficiency class(es) D

Safety:
- The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation.
Overvoltage Protection:
- The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
- For additional protection against transients, it is recommended to use separate overvoltage protection components.
Luminaire Specifications:
- Lamp Module Connected Wattage: 7.9 W
- Connected luminaire Wattage: 10 W
- Rated Temperature: 23,296 K3
- Ambient Temperature: LED-0529/930
Facility:
- LEDs are high-quality electronic components. Avoid touching the light output opening of the LED directly during installation or relamping.

Q: Can I install the luminaire myself?
- A: Installation and commissioning should only be carried out by a qualified electrician to ensure safety and proper functioning.
Q: What is the weight of the product?
- A: The product weighs 2.2 kg.
Q: What is the impact strength of the luminaire?
- A: The luminaire has an impact strength of IK06.

Ceiling and wall luminaire for indoor use

$BEGA-23296K4-Ceiling-and-wall-luminaire-for-indoor-use-FIG-1 $1$$

Application

Ceiling and wall luminaire indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks.
They are ideal for places where a soft and uniform lighting distribution is required.

Metal housing, finish colour white
Hand-blown opal glass, with sliding-bolt closure
2 mounting holes ø 5.5mm
Distance apart 155mm
1 cable entry for through-wiring for mains cable
Connecting terminal 2.5@ with plug connection
Earth conductor connection
LED power supply unit 220-240 V x 0/50-60 Hz
DC 170-280 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Impact strength IK06
Protection against mechanical impacts < 1 joule
- – Safety mark
- – Conformity mark
Weight: 2.2 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

23 296K3

23 296K4

LEDs are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Disassemble the LED module.
Loosen LED connection and earth connection (plug connection).
Dismantle the mains supply cable max. 80 mm.
Lead mains supply cable through the cable entry into the luminaire housing.
Fix the luminaire housing with enclosed or any other suitable fixing material onto the mounting surface.
It is imperative to use the enclosed gaskets.
Make an earth conductor connection.
Push silicone sleeves over the lines and make an electrical connection.
Make an earth connection between the LED module and luminaire housing (plug connection).
Push the plug into the coupler as far as it will go.
Assemble LED module.
Tighten the screws evenly (max. 0,8 Nm).
Please observe that the LED module is not damaged mechanically.

ATTENTION!

It is mandatory to make sure not to damage the wires while fixing the opal glass.
Insert the opal glass into the luminaire housing with sliding bolt glass closure and turn the glass clockwise up to the stop.
Place glass into the luminaire housing with sliding bolt glass closure and observe that the holding spring bolts fit into the notches of the glass.
ATTENTION: Fix the glass to the luminaire housing by turning it clockwise beyond the first resistance, if any, until it is locked.
Thus, you reach a safe and vibration-resistant holding of the glass.
To release the glass from the luminaire housing, turn it counterclockwise.

Replacement of the LED module · Maintenance

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Unscrew the glass from the luminaire housing by turning it counterclockwise.
Clean glass and luminaire regularly with solvent-free cleansers from dirt.
Please follow the installation instructions for the LED module.
Screw in the glass by turning it clockwise as far as it will go.
A broken glass must be replaced.

Spares