BEGA 12132K27 Ceiling Light and Wall Light Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
12132K27 Ceiling Light and Wall Light
**Instruction Manual
**
12132K27 Ceiling Light and Wall Light
Technical amendments reserved
Ceiling and wall luminaire for indoor use
Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.
Product description
Metal housing, finish colour white
Hand-blown opal glass, satin matt, with bayonet closure 2 mounting holes ø 5.5
mm
Distance apart 180 mm 2 cable entries for through-wiring for mains cable up to
ø 10.5 mm max. 3 × 1.5◻
Connection terminal 2.5◻
Earth conductor connection
LED power supply unit 220-240V ∼ 50-60 Hz
BEGA Thermal Switch
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Impact strength IK02
Protection against mechanical impacts < 0.2 joule
– Safety mark
****– Conformity mark
Weight: 2.9 kg
This product contains light sources of energy efficiency class(es) D, E
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 8.2 W |
|---|---|
| Luminaire connected wattage | 10.3 W |
| Rated temperature | ta= 25 °C |
| Ambient temperature | ta max = 35 °C |
12 132 K27
| Colour temperature | 2700 K |
|---|---|
| Colour rendering index | CRI > 90 |
| Module luminous flux | 1165 lm |
| Luminaire luminous flux | 689 lm |
| Luminaire luminous efficiency | 66,9 lm / W |
12 132 K3
| Colour temperature | 3000 K |
|---|---|
| Colour rendering index | CRI > 90 |
| Module luminous flux | 1205 lm |
| Luminaire luminous flux | 712 lm |
| Luminaire luminous efficiency | 69,1 lm / W |
12 132 K4
| Colour temperature | 4000 K |
|---|---|
| Colour rendering index | CRI > 90 |
| Module luminous flux | 1255 lm |
| Luminaire luminous flux | 742 lm |
| Luminaire luminous efficiency | 72 lm / W |
Luminaire with trim ring: Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Pass the mains supply cable through the grommet into luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material on
to the mounting surface.
It is imperative to use the enclosed gaskets.
Dismantle the mains supply cable approx. 60 mm.
Make earth and electrical connection to the terminals.
Place glass to the luminaire housing and observe that the cam pins fit into
the notches of the glass.
Screw in glass by turning it clockwise.
Thus, you reach a safe and vibration- resistant holding of the glass.
To release the glass from the luminaire housing, turn it counter-clockwise.
Replacement of the LED unit
The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to
those of the LED units originally fitted. The LED unit can be replaced by
qualified persons using standard tools.
Disconnect from main supply.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Replace the LED unit.
Screw in glass by turning it clockwise.
Defective glass must be replaced.
Accessory · Trim rings
For this luminaire metal trim rings in 3 enamel surfaces are optional
available.
Trim rings are accessories and must be ordered separately.
| Item | Part. No |
|---|---|
| Colour white | 13 001 |
| Colour palladium | 13 002 |
| Colour glossy silver | 13 003 |
Spares
| Spare glass | 11 003 321 .0R G |
|---|---|
| LED unit 2700 K | 75 001 897 .1K 27 |
| LED unit 3000 K | 75 001 897 .1K 3 |
| LED unit 4000 K | 75 001 897 .1K 4 |
BEGA Gantenbrink-Leuchten KG ·
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>