BEGA 84963 RGBW Compact Floodlight Instructions

Table of Contents

Specifications:
- Application: Compact floodlight with a mounting box for permanent installations on a wall, under a ceiling, or on a pillar
- Control: DALI colour light control
- Luminaire connected wattage: 24 W
- Colour temperature: 4000 K
- Luminaire luminous flux: 1288 lm
- Luminaire luminous efficiency: 53.7 lm/W

Safety:
- The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should perform installation and commissioning to avoid any damage due to improper use or installation.
Overvoltage Protection:
- The electronic components have protection against overvoltage.
- For additional protection against transients, consider using separate overvoltage protection components available on the manufacturer’s website.
Installation:
- Handle LED components with care to avoid direct contact with the light output opening during installation or relamping.
- To install the floodlight unit, follow the provided sketch, align it on the mounting plate, and securely screw it together.
- To adjust the beam direction, use a hexagon socket head wrench size 5 mm to loosen the joint screw, set the desired direction, and then tighten the joint screw to a torque of 7 Nm.
Maintenance:
- The connecting cable between the mounting box and floodlight should be regularly inspected for damages and replaced by a qualified electrician if needed.
Accessories:
- Optional accessories like optical filters and shields are available. Request a separate set of instructions for their use if needed.

Q: Can I install the floodlight without the help of a qualified electrician?
- A: No, installation and commissioning must only be done by a qualified electrician to ensure safety and proper functioning.
Q: Where can I find replacement parts for the luminaire?
- A: Replacement parts like LED covers, trim rings, power supply units, modules, reflectors, and gaskets can be found using the provided part numbers.

Compact floodlight RGBW

$BEGA-84963-RGBW-Compact-Floodlight-FIG-1 $1$$

Application

Compact floodlight with a mounting box for permanent installations on a wall, under a ceiling or on a pillar.
The floodlight can be controlled by DALI colour light control.

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Clear safety glass
The reflector surface is made of pure aluminium
The rotation range of floodlight is 350°
Swivel range -15°/+90°
Mounting box with 2 fixing holes ø 4.8mm · 67mm spacing
2 cable entries for through-wiring of mains supply cable ø 7-10.5mm, max. 5G1.5@
Connecting terminal 2.5@ with plug connection
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK08
Protection against mechanical impacts < 5 joule
– Safety mark
– Conformity mark
Wind catching area: 0.024 m²
Weight: 2.0 kg
This product contains light sources of energy efficiency class(es) F

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the hexagon socket head screws (wrench size 3 mm) at the mounting box and remove the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Note the position of application of the mounting plate “arrow down”.
Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make an earth conductor connection.
Push silicone sleeves over the lines and make an electrical connection to the terminal (plug connection).
For digital control please use the 2-pole plug connector DA, DA.
In case this connector is not used the luminaire will be operated at full light output.
Push the plug into the coupler as far as it will go.
Make sure that the gasket is positioned correctly. $BEGA-84963-RGBW-Compact-Floodlight-FIG-1 $3$$
Place the floodlight unit onto the mounting plate as displayed in the sketch, and align and screw it together firmly.

Adjustment of beam direction:

Undo the joint screw (hexagon socket head wrench size 5 mm) and set the desired beam direction.
Tighten the joint screw.
Torque = 7Nm.

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Lamp

Lighting technology

Wide beam light distribution
Half beam angle 24°
For special lighting applications, an optical filter can be used to change the symmetrical light cone into a flat beam light distribution.

Maintenance

The connecting cable between the mounting box and the floodlight has to be inspected for obvious damages and has to be replaced by a qualified electrician only.

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools.
Disconnect the system from the power supply.
Open the floodlight:
Loosen the back locking pin (hexagon socket wrench size 2mm) in the trim ring.
Remove the trim ring along with the safety glass and reflector by twisting it anti-clockwise.
Replace the LED module.
Please follow the installation instructions for the
LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Place the trim ring with glass and reflector on the floodlight housing so that the notches in the trim ring and luminaire housing sit on top of each other.
Twist on the trim ring clockwise as far as the stop. Screw in the locking pin.