BEGA 77 479 Surface Floodlight Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 77 479 Surface Floodlight
Instructions For Use
Application
Floodlight with mounting bush G½. for broad spread light distribution.
The floodlight can be bolted together with any female thread G½ according to
ISO 228.
Product Description
Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Safety glass with optical structure
Silicone gasket
Reflector made of pure anodised aluminium
Rotation range of floodlight 350°
Swivel range -35°/+90°
Mounting bracket with G½ threaded connection
Thread length: 11mm
Connecting cable X05BQ-F 5G1mm²
Cable length 1m
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V 0/50-60 Hz
During DC operation the LED power is reduced to 15%
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK07
Protection against mechanical impacts < 2 joule
– Safety mark
– Conformity mark
Wind catching area: 0.022 m²
Weight: 1.3 kg
This product contains light sources of energy efficiency class(es) D
Dimension
Lighting technology
Half beam angle 76/89°
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage Protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71320.
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Screw floodlight mounting bush G½ firmly into the female G½ thread provided on
site or into BEGA accessory.
Torque of the mounting bush G½ = 20Nm.
Secure bolted connection against loosening.
Check earth conductor connection between mounting bush G½ and female thread G½
provided on site.
The electrical connection must be carried out with matching protection class
and safety class, strain-relieved, with suitable connection terminals (not
included in the scope of delivery) at the luminaire power supply cable.
Note correct configuration of the mains supply cable.
Make mains supply connection at the brown (L), blue (N) and green-yellow lead
( ).
The connection of the control cables is achieved by means of the both leads
marked with DALI.
In case these leads are not used the luminaire will be operated at full light
output.
Adjust the floodlight.
Undo the joint screw and adjust the floodlight.
Tighten the joint screw.
Torque = 7Nm.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Lamp
Module connected wattage| 17.6 W
Luminaire connected wattage| 20.5 W
Rated temperature| ta=25 °C
Ambient temperature| ta max=45 °C
77 479K4
Module designation| LED-0313/940
Colour temperature| 4000 K
Colour rendering index| CRI >90
Module luminous flux| 2940 lm
Luminaire luminous flux| 2295 lm
Luminaire luminous efficiency| 112 lm/W
77 479K3
Module designation| LED-0313/930
Colour temperature| 3000 K
Colour rendering index| CRI >90
Module luminous flux| 2780 lm
Luminaire luminous flux| 2170 lm
Luminaire luminous efficiency| 105,9 lm/W
Please note
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Replacing The LED Module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Accessories
| 70 214 | Pole cap for pole ø 48 mm |
|---|---|
| 70 248 | Pole cap for pole ø 60 mm |
| 70 245 | Mounting box |
| 70 252 | General fastener |
| 70 280 | Tube clamp G½ |
| 70 283 | Screw clamp |
| 70 379 | Cross beam G½ |
| 70 889 | Tension belt |
| 71 042 | Adapter for installation on a pole |
| 70 500 | Shield |
For the accessories a separate instructions for use can be provided upon request.
Spares
| Spare glass | 14 000 966 |
|---|---|
| LED power supply unit | DEV-0494/700i |
| LED module 3000 K | LED-0313/930 |
| LED module 4000 K | LED-0313/940 |
| Reflector | 76 001 194 |
| Gasket glass | 83 001 372 |
| Gasket housing | 83 001 386 |
CUSTOMER SUPPORT
BEGA Gantenbrink- Leucite KG ·
Postrace 3160 · 58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>