BEGA 50594.4K3 Wall Washers Instruction Manual

June 1, 2024
BEGA

BEGA 50594.4K3 Wall Washers

Product Specifications:

  • Lamp Module connected wattage: 24.6 W
  • Luminaire connected wattage: 28.1 W
  • Rated temperature: 25°C
  • Ambient temperature: 25°C
  • Colour temperature options: 3000 K, 4000 K
  • Colour rendering index (CRI): > 90
  • Module luminous flux: 3620 lm (3000 K), 3770 lm (4000 K)
  • Luminaire luminous flux: 2571 lm (3000 K), 2678 lm (4000 K)
  • Luminaire luminous efficiency: 91.5 lm/W (3000 K), 95.3 lm/W (4000 K)

Product Usage Instructions

Safety:

The installation and operation of this luminaire should be done in accordance with national safety regulations. Installation and commissioning must be carried out by a qualified electrician to avoid damage due to improper use or installation.

Overvoltage Protection:

The electronic components in the luminaire are protected against overvoltage according to DIN EN 61547. For additional protection against transients, separate overvoltage protection components are recommended, available on the manufacturer’s website.

Installation:

LED components are of high quality, avoid direct contact with the LED light output opening during installation or relamping to prevent damage.

Replacement Parts:

  • Spare glass: 14 001 183 RG DEV-0194/700
  • LED power supply unit: LED-0696/930, LED-0696/940
  • LED module 3000 K: LED-0696/930
  • LED module 4000 K: LED-0696/940
  • Reflector: 76 001 510

Frequently Asked Questions

  • Q: Can I install the luminaire myself?
    • A: No, installation and commissioning should only be done by a qualified electrician.
  • Q: Where can I find overvoltage protection components?
    • A: Overvoltage protection components are available on the manufacturer’s website at www.bega.com.

Dimension

Wall washer for indoor useBEGA-50594-4K3-Wall-Washers-
fig-1

Instructions for use

Application

Wall washer · indoor luminaire for the glare-free illumination of wall surfaces with the mounting surface being the reflection surface. The light emits upwards and downwards.

Product Description

  • Die-cast aluminium and aluminium housing, finish Colour palladium
  • Crystal glass, inside matt
  • Reflector made of pure anodised aluminium
  • 2 mounting holes ø 4.8 mm
  • Distance apart 200 mm
  • 2 cable entries for through-wiring for mains
  • cable up to ø 8 mm max. 3 × 1.5
  • Connection terminal 2.5
  • Earth conductor connection
  • LED power supply unit
  • 220-240 V 0/50-60 Hz
  • DC 176-276 V
  • BEGA Thermal Switch®
  • Temporary thermal shutdown to protect
  • temperature-sensitive components
  • Safety class I
  • Impact strength IK07
  • Protection against mechanical
  • impacts < 2 joule
  • Safety mark
  • CE Conformity mark
  • Weight: 1.9 kg
  • This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

  • Module connected wattage 24.6 W
  • Luminaire connected wattage 28.1 W
  • Rated temperature ta = 25 °C
  • Ambient temperature ta max = 25 °C

50 594.4 K3

  • Module designation 2x LED-0696/930
  • Colour temperature 3000 K
  • Colour rendering index CRI > 90
  • Module luminous flux 3620 lm
  • Luminaire luminous flux 2571 lm
  • Luminaire luminous efficiency 91,5 lm / W

50 594.4 K4

  • Module designation 2x LED-0696/940
  • Colour temperature 4000 K
  • Colour rendering index CRI > 90
  • Module luminous flux 3770 lm
  • Luminaire luminous flux 2678 lm
  • Luminaire luminous efficiency 95,3 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Undo the screws and lift off the luminaire top. \Loosen earth connection (plug connection) and LED-connection between luminaire top and luminaire base. Lead the mains supply cable through the cable entry of the luminaire base. Note the position of application of the luminaire “arrow down”. Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection. Make earth connection (plug connection) and LED connection between the luminaire top and luminaire base again. Install the luminaire top part, adjust it and tighten screws evenly.

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools. Disconnect the system and open the luminaire. Uninstall the reflector. Please follow the installation instructions for the LED module. Install the reflector. The defective glass must be replaced. Close the luminaire

Replacement of the glass

Undo the screws and lift off the luminaire top. Loosen earth connection (plug connection) and LED-connection between luminaire top and luminaire base. Loosen the reflector screws, separate the earth connection and remove the reflector. Loosen screws of the glass retaining springs and remove glass retaining springs from the luminaire top. Remove damaged glass. Insert replacement glass. Reinstall glass retaining springs and tighten screws on both sides. Insert reflector into luminaire top part, make earth connection to reflector and tighten reflector screws (0,6 Nm). Make an earth connection (plug connection) and LED-connection between the luminaire top and luminaire base again. Install the luminaire top part, adjust it and tighten the screws evenly.

Spares

  • Spare glass 14 001 183 RG
  • LED power supply unit DEV-0194/700
  • LED module 3000 K LED-0696/930
  • LED module 4000 K LED-0696/940
  • Reflector 76 001 510

BEGA Gantenbrink-Leuchten KG

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals