BEGA 84098K4 Surface Washer Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 84098K4 Surface Washer
Surface washer
Instructions for use
Overvoltage protection
Safety
Lamp
Installation
Accessory
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 84098K4 Surface Washer

Specifications

Material: Aluminium alloy, aluminium, stainless steel
Colour Options: Graphite or Silver
Reflector: Pure aluminium
Power Supply: 50-60 Hz DC 176-264 V
Safety Class: I
Protection Class: IP 65
Weight: 3.2 kg

Installation

The installation and operation must comply with national safety regulations.
Installation and commissioning should only be carried out by a qualified electrician.
Ensure the luminaire is mounted securely on the wall surface.

LED Module Replacement

Locate the label inside the luminaire to identify the LED module.
Disconnect the power supply and open the luminaire carefully.
Follow the installation instructions for replacing the LEDmodule.
Inspect and replace any damaged gaskets or glass components.
Close the luminaire securely after replacing the LED module.

FAQ
Q: Can the luminaire be installed in any position?
A: Yes, the luminaire can be installed in any burning position.

Surface washer

$BEGA-84098K4-Surface-Washer-$2$$

Instructions for use

Application

Wall-mounted surface floodlight with asymmetrical light distribution for lighting wall-, ceiling- and ground surfaces.
The luminaire can be installed in any burning position.

Product description

Luminaire made of aluminum alloy, aluminum and stainless steel
BEGA Unidure® coating technology
Color graphite or silver

Safety glass

The reflector surface made of pure aluminium
Swivel range -30°/+120°
Mounting plate with 2 fixing holes ø 5.5 mm · 70 mm spacing
2 cable entries for through-wiring of mains
supply cable ø 7-10.5 mm, max. 5 G 1.5@
Connecting terminal 2.5@
with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without
switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK08
Protection against mechanical
impacts < 5 joule
– Safety mark
– Conformity mark
Wind catching area: 0.072 m²
Weight: 3.2 kg
This product contains light sources of energy efficiency class(es)

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage 19.4 W
Luminaire connected wattage 22 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C

84 098 K4

Module designation LED-0872/940
Colour temperature 4000 K
Colour rendering index CRI > 90
Module luminous flux 3310 lm
Luminaire luminous flux 2661 lm
Luminaire luminous efficiency 121 lm / W

84 098 K3

Module designation LED-0872/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 3130 lm
Luminaire luminous flux 2516 lm
Luminaire luminous efficiency 114,4 lm / W

Installation

Open mounting box.
Lead mains supply cable through the cable entry into the mounting box.
Fix the mounting box with enclosed or any other suitable fixing material onto the mounting surface.
Note position of application of the mounting plate “arrow down”.
Make earth conductor connection and electrical connection to the connecting terminal (plug connection).
Make earth conductor connection between luminaire and mounting plate.
Place floodlight onto mounting plate and fix it. Undo joint screw and adjust the slope angle of the surface floodlight.
Tighten joint screw firmly.
Torque = 14 Nm

Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.