BEGA 84847K3 Performance Floodlight Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 84847K3 Performance Floodlight
Product Usage Instructions
Instructions for use
Installation
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 84847K3 Performance Floodlight

Specifications

Power Consumption of 84 847 : 0.05 A
Lamp Module Connected Wattage: 8.1 W
Luminaire Connected Wattage: 9.6 W
Rated Temperature (ta): 25°C
Ambient Temperature (ta max): 50°C
Colour Temperature: LED-0800/930 3000 K
Colour Rendering Index (CRI): > 90
Module Luminous Flux : 1255 lm
Luminaire Luminous Flux : 960 lm
Luminaire Luminous Efficiency : 100 lm/W

Product Usage Instructions

Safety

The installation and operation of this luminaire must comply with national safety regulations. The manufacturer is not liable for damage due to improper use or installation.

Installation

Unscrew the hexagon socket screws on the sides of the connection adapter using a 3 mm wrench.
Screw the corresponding accessory to the floodlight with a torque of 5 Nm.
Plug the floodlight’s connecting cable into the plug contact of the country-specific mains plug or distribution box.
Ensure a connecting cable length of not more than 50 m per luminaire.
To adjust the beam direction, undo the joint screw with a 5 mm wrench, set the desired direction, and tighten the screw with a torque of 7 Nm.

Maintenance

Check the connecting cable for external damage regularly and replace it only with the help of a qualified electrician.

Note

Do not remove the desiccant bag from the luminaire housing as it is essential for removing residual moisture.

Accessories

The following combination options are available for fitting to floodlights with connection adapter:

71 118 Shield
71 120 Exchangeable lens flat beam

FAQ

Q: Can I use this luminaire outdoors?
- A: Yes, this luminaire can be used outdoors, but make sure tofollow all safety guidelines and protection against environmental elements.
Q: How often should I check the connecting cable for damage?
- A: It is recommended to check the connecting cable for damage regularly, at least once every few months, to ensure safe operation.

Performance floodlight BEGA UniLink

BEGA-84847K3-Performance-Floodlight-FIG2

Instructions for use

Application

Performance floodlight BEGA UniLink® with connection adapter for use in combination with various accessories, e.g. for mounting on trees, pipes or wooden structures.
A separate mains plug must be ordered in order to connect the floodlight to the mains. The various country-specific mains plug with 0.5m connecting cable, as well as extension cables and five-way distribution boxes are available as accessories.

Product Description

Luminaire made of aluminum alloy, aluminum and stainless steel
BEGA Unidure® coating technology
Clear safety glass
Silicone gasket
The reflector surface made of pure aluminium
Optical silicone lens · BEGA Hybrid Optics®
The rotation range of floodlight is 360°
Swivel range -40°/+75°
5m mains supply cable
X05RN-F FEP 2×1@ + 1G2,5@ with
BEGA UniLink® plug-in connector
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240V 50-60 Hz
BEGA Thermal Switch®
Temporary thermal shutdown to protect
temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK08
Protection against mechanical
impacts < 5 joule
– Conformity mark
Weight: 2.2 kg
This product contains light sources of energy efficiency class(es) E

Safety

The installation and operation of this luminaire are subject to national safety regulations.The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Total load

When configuring your lighting system, please ensure that the maximum power consumption of 6A is not exceeded. Information on power consumption can be found in the instructions for use and data sheets for all BEGA UniLink® luminaires.

Power consumption of 84 847 : 0,05 A

Lamp

Module connected wattage : 8.1 W
Luminaire connected wattage : 9.6 W
Rated temperature: ta=25 °C
Ambient temperature: ta max=50 °C

84 847K3

Module designation: LED-0800/930
Colour temperature: 3000 K
Colour rendering index : CRI >90
Module luminous flux : 1255 lm
Luminaire luminous flux :960 lm
Luminaire luminous efficiency : 100 lm/W

84 847K4

Module designation :LED-0800/940
Colour temperature :4000 K
Colour rendering index : CRI >90
Module luminous flux : 1275 lm
Luminaire luminous flux :975 lm
Luminaire luminous efficiency: 101,6 lm/W

Light technique

Symmetrical wide beam light distribution
Half beam angle 46°
For special lighting applications, the symmetrical light cone can be changed to a flat beam using an additional diffuser lens.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Caution:

The BEGA UniLink® plug connectors may only be connected and disconnected in a voltage-free state.

Installation

Unscrew the hexagon socket screws (wrench size 3 mm) on the sides of the connection adapter and screw the corresponding accessory to the floodlight.
Torque = 5Nm.

Plug the floodlight’s connecting cable into the plug contact of the connecting cable with the country-specific mains plug, or into the distribution box or extension cable.
To ensure a sufficiently low protective conductor resistance (loop resistance), the connecting cable of each luminaire in the system must not exceed a length of 50m from the entry point.

Adjustment of beam direction:

Undo joint screw (hexagon socket head wrench size 5 mm) and set the desired beam direction.
Tighten the joint screw.
Torque = 7Nm.

Please note:

Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Maintenance

The connecting cable must be checked for external damage and may only be replaced by a qualified electrician.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light color and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.

Open the floodlight:

Undo locking pin (hexagon socket head wrench size 2.5 mm) on the back side of the floodlight housing.
Remove the trim ring along with the safety glass and reflector by twisting it counterclockwise.
Replace LED module.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Place trim ring with glass and reflector on the floodlight housing in such a way that the notches in the trim ring and floodlight housing align on top to each other.
Twist on the trim ring clockwise as far as the stop. Tighten the locking pin.

Accessories

The following combination options are available for fitting to floodlights with connection adapter:

71 223 Screw clamp with connection adapter 71 224 Tube clamp with connection adapter 71 225 Lashing strap with connection adapter 71 226 General fastener with connection adapter
71 227 G½ mount with connection adapter
71 118 Shield
71 120 Exchangeable lens flat beam Country-specific mains plugs with 0.5 m connecting cable
71 180 Plug type F / E: system common in Germany and Europe
71 181 Plug type G: system used in Great Britain (“Commonwealth plug”)
71 182 Plug type J: system common in Switzerland and Liechtenstein
71 183 Plug type L: system common in Italy and Greece
71 184 Plug type K: system common in Denmark and Greenland
71 186 BEGA UniLink® Extension cable 5 m 71 187 BEGA UniLink® Extension cable 10 m 71 188 BEGA UniLink® Extension cable 20 m
71 247 Connecting cable 5 m with free line ends
71 256 Connecting cable 0.5 m with free line ends
71 189 BEGA UniLink® Five-way distribution box