BEGA 84808 Garden and Pathway Luminaire Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 84808 Garden and Pathway Luminaire
Specifications
Product Usage Instructions
FAQ
Dimension
Instructions for use
Product Description
Safety
Overvoltage protection
Installation
Replacing the LED module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 84808 Garden and Pathway Luminaire

Specifications

Application: Garden and pathway luminaires for glare-free illumination of surfaces from low mounting heights.
Dark Sky: The light is directed evenly and efficiently onto the surface with less than 1% of the luminous flux emitted into the upper halfspace.
Safety: Installation and operation are subject to national safety regulations. Must be installed and commissioned by a qualified electrician.
Overvoltage Protection: Electronic components are protected against overvoltage according to DIN EN 61547.
Lamp Module Connected Wattage: 5.8 W
Luminaire Connected Wattage: 7 W
Rated Temperature: 25°C to 55°C
Ambient Temperature: Max 55°C
LED-1171/830 Module:
- Colour Temperature: 3000 K
- Colour Rendering Index (CRI): >80
- Luminous Flux: 1120 lm
- Luminaire Luminous Flux: 513 lm
- Luminaire Luminous Efficiency: 73.3 lm/W

Product Usage Instructions

Installation:

Ensure the luminaire is mounted securely at a low height for optimal glare-free illumination.
Installation and commissioning must only be performed by a qualified electrician.
Refer to national safety regulations for proper installation guidelines.

Maintenance:

Do not remove the desiccant bag from the luminaire housing as it helps remove residual moisture.
Regularly check for any signs of damage or wear and tear on the luminaire.

Replacement Parts:

If replacement parts are needed, refer to the following:

LED Power Supply Unit: DEV-0304/350
LED Module 3000 K: LED-1171/830
Gasket: 83 002 083

FAQ

Q: Can I install the luminaire myself?
- A: No, installation and commissioning must only be carried out by a qualified electrician to ensure safety and proper functioning.
Q: What should I do if the luminaire shows signs of damage?
- A: If you notice any damage, stop using the luminaire and contact a qualified electrician for inspection and possible repair.

Dimension

$BEGA-84808-Garden-and-Pathway-Luminaire-fig $1$$

Instructions for use

Application

Garden and pathway luminaires for glare-free illumination of surfaces from low mounting heights.

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Safety glass with optical structure
Luminaire with anchorage unit for fixing in the soil
The anchorage unit is made of galvanised steel according to EN ISO 1461
Connection set with gasket insert and dripproof
cap for through-wiring power connecting
cables of ø 10–13.5 mm, max. 3 × 2.5@
BEGA Ultimate Driver®
LED power supply unit
220-240 V 0/50-60 Hz
DC 176-264 V
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical impacts < 1 joule
Safety mark
Conformity mark
Weight: 6.4 kg
This product contains light sources of energy efficiency class(es) C

Dark Sky

The light of this luminaire is directed evenly and highly efficiently onto the surface to be illuminated. Less than 1 % of the luminaire luminous flux is emitted into the upper halfspace of the luminaire.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected wattage 5.8 W
Luminaire connected wattage 7 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 55 °C

84 808 K3

Module designation LED-1171/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 1120 lm
Luminaire luminous flux 513 lm
Luminaire luminous efficiency 73,3 lm / W

Installation

The base of the luminaire must not be lower than the upper edge of the floor covering. A cable length of 0,4 m above the mounting surface is required for the electrical connection. Remove the hexagon socket screws (wrench size 3 mm) at the base of the luminaire and remove the anchorage unit. Pass the underground cable into the anchorage unit from underneath. When installing the anchorage unit, make sure that the tubes are absolutely vertical and 120 mm above the upper edge of the floor covering. The luminaire is connected to the power supply using the supplied connection set. Complete the installation according to the installation instructions shown. Place the luminaire on the anchorage unit via the drip-proof cap and secure in place

Please note:

Do not remove the desiccant bag from the luminaire housing. It is needed to remove residual moisture.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners

$BEGA-84808-Garden-and-Pathway-Luminaire-fig $2$$

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified person using commercially available tools. Disconnect the system and open the luminaire. To do this, insert a small screwdriver into the two small openings next to the light emission. Press the screwdriver inwards and remove the housing. Loosen the 4 hexagon socket screws (wrench site 2.5 mm) on the back and lift off the top part of the housing. Disconnect the earth conductor plug connector on the top part of the housing. Loosen the two screws (Torx driver T10) and remove the electrical unit from the bottom part of the housing.

Please note:

Do not remove the desiccant pouch from inside\ the bottom part of the housing. It is needed to remove residual moisture. \Replace LED module. Please follow the installation instructions for the LED module. Insert the electrical unit into the bottom part of the housing and secure it in place. Ensure that the earth wire and the toothed lock washers are in the correct position. Place the earth conductor plug connector onto\ the top part of the housing. Assemble the housing components and fasten them evenly using countersunk screws. Make sure that the protective conducting wire is not clamped between the upper and lower part of the housing. Evenly guide the housing into the luminaire profile and press down until it audibly clicks into place on both sides.

Spares