BEGA 51 298.6 Indoor Wall Luminaire Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 51 298.6 Indoor Wall Luminaire
Specifications
FAQ
Dimension
Instructions for use
Product description
Installation
Replacing the LED module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 51 298.6 Indoor Wall Luminaire

Specifications

Lamp Module connected wattage: 34.8 W
Luminaire connected wattage: 38.5 W
Rated temperature: 25-35°C
Ambient temperature: 51-298.6 K3
Colour temperature: 3000 K
Colour rendering index (CRI): > 90
Module luminous flux: 5400 lm
Luminaire luminous flux: 3420 lm
Luminaire luminous efficiency: 88.8 lm/W

Product Usage Instructions

Overvoltage Protection:

The luminaire’s electronic components are protected against overvoltage according to DIN EN 61547. For additional protection against transients, separate overvoltage protection components are recommended and available on the manufacturer’s website.

Safety:

Installation and operation of the luminaire must comply with national safety regulations. Only a qualified electrician should perform installation and commissioning. The manufacturer is not liable for damage due to improper use or installation. Any modifications to the luminaire should be carried out by authorized personnel.

Replacement Parts:

If replacement parts are needed, the following are available:

LED power supply unit: DEV-0305/700i
LED module 3000 K: LED-1403/930, LED-1461/930

FAQ

Q: Can I install the luminaire myself?
- A: No, installation and commissioning should only be done by a qualified electrician to ensure safety and compliance with regulations.
Q: Where can I find additional overvoltage protection components?
- A: Additional overvoltage protection components can be found on the manufacturer’s website at www.bega.com.

Dimension

BEGA-51-298-6-Indoor-Wall-Luminaire-
fig-1

Instructions for use

Application

Wall luminaire · Indoor luminaire with 2 ring-shaped light sources for unshielded and uniform light, light-diffusing silicone diffusers and metal rings. As single luminaires or in arrangements, they are creative lighting design solutions for interior design.

Product description

Ring made of metal and luminaire housing made of synthetic material, surface Colour velvet copper
Round inlay made of metal, finish Colour velvet copper
Diffusor made of translucent, ageing-resistant silicone
Mounting plate with 2 fixingholes ø 6 mm · 85 mm spacing
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connecting terminals 2.5@
Earth conductor connection
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1 LED power supply unit
220-240 V 0/50-60 Hz
DC 196-250 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Conformity mark
Weight: 1.2 kg

This product contains light sources of energy efficiency class(es) D

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage 34.8 W
Luminaire connected wattage 38.5 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 35 °C

51 298.6 K3

Module designation
1x LED-1403/930, 1x LED-1461/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 5400 lm
Luminaire luminous flux 3420 lm
Luminaire luminous efficiency 88,8 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Undo the hexagon socket head screw (wrench size 1,5 mm) and remove mounting plate from luminaire housing. Pass the power connecting cable through the cable entry in the mounting plate. Note position of application of the mounting plate “arrow down”. Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface. Establish earth conductor connection to the earth conductor connection screw and make the electrical connection to the terminals. The two connecting terminals marked DA, DA are provided for digital control purposes. If these terminals are not assigned, the luminaire will work with full light output. Insert the connection terminals into the luminaire housing. BEGA-51-298-6-Indoor-Wall-
Luminaire-fig-4

Position the luminaire housing in a flat inclination angle over the fastening edge of the mounting plate and swing in. The luminaire can be rotated 350° on the mounting plate. Align luminaire housing and tighten (max. 0.25 Nm) hexagon socket screw (wrench size 1.5).

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module. It is also listed in the spare parts overview at the end of these instructions for use. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified person using commercially available tools. Disconnect the system from the power supply. Undo the hexagon socket head screw (wrench size 2.5 mm) and remove luminaire from mounting plate. Remove the connecting lines from the terminals and place the front of the luminaire on a soft surface. Open the luminaire housing: Remove the 6 internal Torx screws (T20) and remove the bottom part of the housing from the top part of the housing. Disconnect the lines of the luminaire cable from the 4 terminals and remove the terminals. Remove the LED module with the diffuser from the holder. Install the replacement module. Please follow the installation instructions for the new LED module. A defective LED-module (silicone diffusor) must be replaced. Close the luminaire housing: Guide the bottom part of the housing with the drilled hole over the positioning pin of the top part of the housing and place it on top. Retighten the 6 Torx screws (T20 max. 1.2 Nm). Re-attach the terminals to the wires of the luminaire cable. Make the electrical connection to the terminals. Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N). The two connecting terminals marked DA, DA are provided for digital control purposes. If these terminals are not assigned, the luminaire will work with full light output. Position the luminaire housing in a flat inclination angle over the fastening edge of the mounting plate and swing in. Align luminaire housing and tighten (max. 0.25 Nm) hexagon socket screw (wrench size 1.5).

Spares