BEGA 85 173 UniLink Performance Floodlight Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 85 173 UniLink Performance Floodlight
Performance floodlight BEGA UniLink
Instructions for use
Product Description
Installation
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 85 173 UniLink Performance Floodlight

Performance floodlight BEGA UniLink

BEGA-85-173-UniLink-Performance-Floodlight-fig-

Instructions for use

Application
Performance floodlight BEGA UniLink® with connection adapter for use in combination with various accessories, e.g. for mounting on trees, pipes or wooden structures. A separate mains plug must be ordered to connect the floodlight to the mains. The various country-specific mains plug with 0.5m connecting cable, as well as extension cables and five-way distribution boxes are available as accessories.

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Clear safety glass
Silicone gasket
The reflector surface is made of pure aluminium
Optical silicone lens · BEGA Hybrid Optics
The rotation range of floodlight is 360°
Swivel range -40°/+75° 5m mains supply cable
X05RN-F FEP 2×1+ 1G2,5 with
BEGA UniLink plug-in connector
Complies with flicker requirements by IEEE 1789
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit220-240 V y 50/60 Hz
BEGA Thermal Switch
Temporary thermal shutdown to protect
temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical
impacts < 1 joule
Conformity mark
This product contains light sources of energy efficiency class(es) E

Safety
The installation and operation of this luminaire are subject to national safety regulations. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Total load

When configuring your lighting system, please ensure that the maximum power consumption of 6A is not exceeded.
Information on power consumption can be found in the instructions for use and data sheets for all BEGA UniLink® luminaires.
Power consumption of 85 173: 0,12 A

Lamp

Module connected wattage 24.1 W
Luminaire connected wattage 27 W
Rated temperature ta=25 °C
Ambient temperature ta max=30 °C

85 173K3

Module designation LED-0800/930
Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 3350 lm
Luminaire luminous flux 2472 lm
Luminaire luminous efficiency 91,6 lm/W

85 173K4

Module designation LED-0800/940
Colour temperature 4000 K
Colour rendering index CRI >90
Module luminous flux 3400 lm
Luminaire luminous flux 2509 lm
Luminaire luminous efficiency 92,9 lm/W

Lighting technology

Symmetrical wide beam light distribution
Half beam angle 45°
For special lighting applications, the symmetrical light cone can be changed to a flat beam using an additional diffuser lens.

Caution
The BEGA UniLink® plug connectors may only be connected and disconnected in a voltage-free state.

Installation

Unscrew the hexagon socket screws (wrench size 3 mm) on the sides of the connection adapter and screw the corresponding accessory to the floodlight.
Torque = 5Nm.
Plug the floodlight’s connecting cable into the plug contact of the connecting cable with the country-specific mains plug or into the distribution box or extension cable.
To ensure a sufficiently low protective conductor resistance (loop resistance), the connecting cable of each luminaire in the system must not exceed a length of 50m from the entry point.

Adjustment of beam direction

Undo the joint screw (hexagon socket head wrench size 5 mm) and set the desired beam direction.
Tighten the joint screw.
Torque = 7Nm.

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Maintenance
The connecting cable must be checked for external damage and may only be replaced by a qualified electrician.

Please note

Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Replacing the LED module
The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system.

Open the floodlight

Undo the locking pin (hexagon socket head wrench size 2.5 mm) on the back side of the floodlight housing.
Remove the trim ring along with the safety glass and reflector by twisting it counterclockwise.
Replace the LED module.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Place the trim ring with glass and reflector on the floodlight housing in such a way that the notches in the trim ring and floodlight housing align on top of each other.
Twist on the trim ring clockwise as far as the stop. Tighten the locking pin.

Accessories

The following combination options are available for fitting to floodlights with connection adapter

71 223 Screw clamp with connection adapter
71 224 Tube clamp with connection adapter
71 225 Lashing straps with connection adapter
71 226 General fasteners with connection adapter
71 227 G½ mount with connection adapter
Shields and diffuser lenses that alter the light distribution are available as accessories for these floodlights.
71 290 Exchangeable lens flat beam
71332 Shield
71 335 Cylindrical shield
Country-specific mains plug with 0.5m connecting cable71180
Plug type F / E: system common in Germany and Europe
71181 Plug type G: system used in Great
Britain (“Commonwealth plug”)
71182 Plug type J: system common in
Switzerland and Liechtenstein
71183 Plug type L: system common in Italy and Greece
71184 Plug type K: system common in
Denmark and Greenland
BEGA UniLink® extension cables with socket and plug
71 186 BEGA UniLink® Extension cable 5m
71 187 BEGA UniLink® Extension cable 10m
71 188 BEGA UniLink® Extension cable 20m
BEGA UniLink® connecting cables with a plug connector and one free cable end to connect to e.g. a conventional connection box
71 247 Connecting cable 5m with free-line ends
71 256 Connecting cable 0.5m with free-line ends

BEGA UniLink distribution box with five connection sockets for the connection of BEGA UniLink luminaires, extension cables or additional five-way distribution boxes 71 189 BEGA UniLink Five-way distribution box For the accessories separate instructions for use can be provided upon request.

Spares