OPT7 Aura Pro Motorcycle LED Light Kit Installation Guide
- June 2, 2024
- OPT7
Table of Contents
OPT7 Aura Pro Motorcycle LED Light Kit
Specifications:
- Product: Motorcycle Cruiser Light Strips
- Components Included:
- Light Strips
- Aura Bluetooth Control Box
- Various Extension Wires
- Power Harness with On/Off Switch
- Zipties
- Y-Splitters
- Maximum Amperage: 10 AMPs
- Operating Temperature: 85°F to 185°F
- Control: OPT7 Connect App
Product Usage Instructions
- Inspect Kit: Ensure all components are included.
- Locate Light Strips: Decide where to place the light strips and ensure wiring length is sufficient for control box installation.
- Connect Wiring: Ensure not to exceed 10 AMPs. Connect the wires carefully following the provided instructions.
- Download App: Scan the QR code on the control box to download the OPT7 Connect App.
- Secure Control Box: Use Velcro or zipties to secure the control box in a desired location away from elements.
- Secure Light Strips: Use zip ties to secure light strips and wiring away from moving components. Waterproof LED connectors using heat shrink tube or electrical tape.
- Pair and Customize: Open the OPT7 Connect App, pair your smartphone, and customize colors and modes for your light strips.
COMPONENTS
INSTALLATION
STEP 1
Inspect kit to ensure all contents was included.
STEP 2
Decide where to locate the light strips and ensure wiring has enough length
for control box to be installed in desired location.
WARNING
- Connecting to more than 10 AMP will override the kit and cause early failure, ensure it is 10AMPs or less!!
- Please ensure that the LED bars or strips/control box/wiring all are mounted in areas where will not exceed 85℃ or 185℉.
IMPORTANT NOTE!! Before You Start
We provide multiple sets of extension wires for you to configure . You can
quickly extend them wherever you want to install.
AUX WIRING FOR A BRAKE LIGHT
You may choose the desired color choice directly on the OPT7 Connect app
This feature will activate when the aux wiring is connected to the trigger
wire for positive (+) wire of your brake light wire.
WARNING NOTE
You should ONLY set the color of your aux wire to “red” in color choices
within the app. If you plan on connecting the aux wire to your brake s ignal
wire.
STEP 3
Scan the QR code on the back of the control box to download the app.
STEP 4
Secure Control box in desired location with Velcro or zipties.
The control box is NOT waterproof. Tuck it away from the elements.
STEP 5
Secure the light strips using the zip ties to tie all the wiring away from the
moving components.
IMPORTANT:
The LED connectors are not waterproof. You will need to use HEAT SHRINK TUBE
or ELECTRICAL TAPE around the LED connectors to ensure the longevity of the
lighting kit.
STEP 6
Open the “OPT7 Connect” App, pair your smart phone to the control box, and
pick your desired color!
OPT7 CONNECT APP
- Colors
- Modes
- Door Assist
- Support
- Ability to control up to
- 4 devices at once
DISCLAIMER
OPT7 Lighting is not liable for damages or personal injuries while installing
this product. The Installation Guide is intended as assistance to reduce setup
time. OPT7 Lighting assumes no responsibility for improper installation.
If you are unfamiliar with your vehicle or inexperienced with aftermarket
upgrades, please seek professional assistance.
OPT7 recommends installation for safety and guidance.
Modified installations or installation recommendations not specified by OPT7
Lighting will void product warranty.
FAQ
Can I connect more than 10 AMPs to the kit?
Connecting more than 10 AMPs will cause early failure of the kit. Ensure it is 10 AMPs or less.
What should I do if my LED bars or strips exceed the recommended temperature range?
Ensure that all components are mounted in areas where the temperature does not exceed 85°F to 185°F.
How do I activate the brake light feature?
Connect the aux wiring to the trigger wire of your brake light wire and set the color choice to red within the OPT7 Connect App.
Is the control box waterproof?
The control box is not waterproof. Keep it away from elements and use Velcro or zipties to secure it.
What should I do if I need additional extension wires?
The kit includes multiple sets of extension wires for you to configure and extend as needed.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>