i3 INTERNATIONAL IP09CP PoE Over Coax Extender User Manual

IP09CP PoE Over Coax Extender
User Manual

IP09CP PoE Over Coax Extender

Thank you for purchasing i3 International’s IP09CP PoE extender (sold in pairs). Use IP09CP as a point-to-point PoE (Power over Ethernet) extender to power IP devices and to carry IP signal for distances of up to 984 feet (300 meters) using existing coaxial cable infrastructure. Use with i3’s line of IP cameras and PoE switches and/or U12 NVR (built-in PoE).

INSTALLATION

FEATURES

• Signal extension up to 984 ft (300 m) over coaxial cable.
• Provides up to 90W power to a remote PoE device.
• Power source from either a PoE switch or an external power adapter.
• Bandwidth up to 100Mbps.
• Supports full duplex and half duplex mode and Auto MDI/MDI-X switching.
• Built-in 30kV ESD, 40A EFT, and 30A surge at RJ45 side.
• Note: Ax85 supports distances up to 328 ft (100 m) only. Mode 1 (Auto Mode, default) is recommended for all IP devices.

REGULATORY NOTICES (FCC CLASS A)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

PACKAGE CONTENTS

1. IP09CPT (Transmitter) x1. Connect to the IP camera.
2. IP09CPR (Receiver) x1. Connect to the PoE switch.
3. Plastic Anchor x8
4. Round Head Screw (Tapping Type) x8

CONNECTORS

Figure 2. IP09CP front and back panels, parts description.

Note. connectors that are not labeled are reserved/not in use.

1. DC Power Connector. Connect to DC48~56V adapter if connecting to a non-PoE switch.
2. Power LED Indication. Indicates device power status. See Table 1.
3. Status Indication. Indicates RJ45 mode. See Table 3.
4. Status Indication. Indicates BNC mode. See Table 4.
5. DIP Switch. Mode selector. See Tables 5, 6.
6. RJ45 Connector. Connect to the PoE IP device. See Table 7.
7. PoE LED Indication. Indicates PoE connection status. See Table 2.
8. BNC Connector. Connect to the second IP09CP device using the RG59 cable, 984 ft (300 m) or less. The link speed is up to 100 Mbps.

Table 1. Power Status LED

Table 2. PoE Status LED

Table 3. Port 1 (RJ45) Mode Status LED

Table 4. Port 2 (BNC) Mode Status LED

Auto Mode / Default (Recommended):
Auto-Negotiation, automatically sets up the link speed and transmission protocol.
Auto Mode with EEE: Energy-efficient Ethernet-based on Auto-Mode

Table 5. Dip Switch Mode Selector

Table 6. Advanced Mode, Manual Link Speed and Mode Dip Switch Configuration

PIN LAYOUT

PIN| Color| PoE Mode A (PoE Switch)| PoE Mode B (PoE Injector)
---|---|---|---
1| White Orange| TX+ / PoE +| TX+
2| Orange| TX-  / PoE +| TX-
3| White Green| RX+ / PoE –| RX+
4| Blue| | PoE+
5| White Blue| | PoE+
6| Green| RX- / PoE –| RX-
7| White Brown| | PoE-
8| Brown| | PoE-

Table 7. RJ45 Pin Layout

SPECIFICATION

| IPO9CPR (Receiver)| IPO9CPT (Transmitter)
---|---|---
Compliance| IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3bw 100BASE-T1 Ethernet IEEE 802.3 N-Way Auto-Negotiation
IEEE 802.3x Full Duplex Operation & Flow Control IEEE 802.3az Energy Efficient Ethernet
IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Bandwidth| 10/100 Mbps
Max. Transmission Distance| 10Mbps @ 984 ft (300 m)
100Mbps @ 328 ft (100 m)
Ports & Interfaces
Input| 1 x 750 BNC| 1 x RJ45
Output| 1 x RJ45| 1 x 750 BNC
Power Interface| 1 x (5.5 x 2.1mm) DC Jack| 1 x (5.5 x 2.1mm) DC Jack
Power
Power Supply| 48 — 56V Regulated| 12 — 56V Regulated
Power Consumption| 1W| 1W
Environmental specifications
Operation| 32-185 °F (0-85 °C);
Storage| -4-185 °F (-20-85 °C);
Humidity| s 95%
Physical Characteristics
Dimensions| 2%” x 5 Vic” x 1 Vs” (67 x 135 x 27mm)
Weight| 0.45 lbs (205 g)| 10.47 lbs (215 g)

Scan this QR code or visit ftp.i3international.com for Annexxus Configuration Tool (ACT) installation and additional documentation.
Contact our Technical Support team at: 1.877.877.7241 or support@i3international.com if you have any questions or concerns regarding camera installation or if you require software services or support.

https://ftp.i3international.com

i3 INTERNATIONAL INC.
1.866.840.0004
www.i3international.com
i3-TRNG-ACCESSORIES-IP09CP .indd

Documents / Resources

| i3 INTERNATIONAL IP09CP PoE Over Coax Extender [pdf] User Manual
IP09CP PoE Over Coax Extender, IP09CP, PoE Over Coax Extender, Over Coax Extender, Coax Extender, Extender
---|---

References

• i3 International FTP Login Page
• Ai Smart Video & Cloud Solutions | i3 International

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>