OPT7 Aura Snowmobile Underglow LED Lighting Kit Installation Guide
- May 15, 2024
- OPT7
Table of Contents
OPT7 Aura Snowmobile Underglow LED Lighting Kit
Specifications
- Main Components: Light Strips, Aura Control Box, Y-Splitters, Hand Held Remote, Keychain Remote, Various Extension Wires, Power Harness with On/Off Switch
- Control Box: Not waterproof
- Extension Wires: Multiple sets provided for customization
- Remote Options: E-Z Remote, Keychain Remote
Product Usage Instructions
Installation:
Step 1 – Location and Wiring:
Decide where to place the light strips ensuring enough wiring length for the control box. Use provided extension wires as needed.
Step 2 – Control Box Placement:
Secure the control box in the desired location using Velcro or zip ties. Remember, the control box is not waterproof.
Step 3 – Light Strip Installation:
Secure light strips using zip ties to keep wiring away from moving components. Use heat shrink tube or electrical tape on LED connectors for longevity.
Step 4 – Remote Operation:
Use the included E-Z Remote or Keychain Remote to select colors or patterns. Follow the remote options for different lighting effects.
Optional Upgrade:
You can upgrade to the Aura Pro Bluetooth Control Box for smartphone control (iOS & Android Compatible).
Disclaimer:
OPT7 Lighting is not liable for damages or injuries during installation. Seek professional assistance if unfamiliar with vehicle modifications. Modified installations not specified by OPT7 will void product warranty.
FAQ
Q: Can I use the product in wet conditions?
A: The control box is not waterproof, so it should be kept away from moisture and elements.
Q: How do I sync the brake light with the default red color?
A: Connect the aux wiring to the positive wire of the brake light to activate the feature. When you apply the brake, it will sync with the red color.
MAIN COMPONENTS
INSTALLATION
STEP 1
Decide where to locate the light strips and ensure wiring has enough length for control box to be installed in desired location.
EXAMPLES
IMPORTANT NOTE!! Before You Start
We provide multiple sets of extension wires for you to configure. You can
quickly extend them wherever you want to install.
# AUX WIRING FOR A BRAKE LIGHT
This feature will activate when the aux wiring is connected to the trigger
wire for positive(+) wire of brake light.
NOTE
The default color is “RED” so that when you apply the brake, it will also sync
with the brake light.
STEP 2
Secure Control box in desired location with Velcro or zipties.
- CONTROL BOX NOT WATERPROOF Ensure the control box is safely and securely hidden from exposing elements of moisture.
STEP 3
Secure the light strips using the zip ties to tie all the wiring away from the
moving components.
IMPORTANT:
The LED connectors are not waterproof. You will need to use HEAT SHRINK TUBE
or ELECTRICAL TAPE around the LED connectors to ensure the longevity of the
lighting kit.
STEP 4
Using the included E-Z Remote or Keychain Remote to select your desired color
or pattern.
AUX WIRING FOR A DOOR/DOME LIGHT
Please scan to see a detail instruction on Door Assist Sync or go to https://wintis.ladesk.com/549690-AURA-Door-AssistAUX-Installation-Guide
OPTIONAL UPGRADE
Upgrade your Aura Original Control Box to the Aura Pro Bluetooth Control Box.
All new AURA Pro Bluetooth is App enabled by a smartphone controller (iOS &
Android Compatible).
DISCLAIMER
OPT7 Lighting is not liable for damages or personal injuries while installing
this product. The Installation Guide is intended as assistance to reduce setup
time. OPT7 Lighting assumes no responsibility for improper installation.
If you are unfamiliar with your vehicle or inexperienced with aftermarket
upgrades, please seek professional assistance.
OPT7 recommends installation for safety and guidance.
Modified installations or installation recommendations not specified by OPT7
Lighting will void product warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>