BEGA 51 222.1 Illuminated Mirror for Indoor Use Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 51 222.1 Illuminated Mirror for Indoor Use
Product Information
Product Usage Instructions
Instructions for use
DIMENSION
Product Description
Safety
FEATURES
Installation
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 51 222.1 Illuminated Mirror for Indoor Use

Product Information

Product Name: Luminaire
Model: LED-1302/930
Colour Temperature: 3000 K
Colour Rendering Index (CRI): > 90
Module Luminous Flux: 7900 lm
Luminaire Luminous Flux: 2837 lm
Luminaire Luminous Efficiency: 48.1 lm/W
Module Wattage: 53.1 W
Luminaire Wattage: 59 W
Rated Temperature: 25-45°C
Ambient Temperature: ta, ta max

Product Usage Instructions

Overvoltage Protection:

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. For additional protection against ransients, it is recommended to use separate overvoltage protection components. These can be found on our website at www.bega.com.

Safety:

The installation and operation of this luminaire should be done in accordance with national safety regulations. Only qualified electricians should perform the nstallation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. If modifications are made to the uminaire, the person responsible for these modifications will be considered the manufacturer.

Installation:

LEDs are high-quality electronic components. During installation or relamping, avoid touching the light output opening of the LED directly. To install the luminaire, follow these steps:

Remove the luminaire housing (reflector) from the packaging.
Pass the power connecting cable through the cable entry into the luminaire housing.
Secure the luminaire housing to the installation surface using the provided fixing materials or other suitable materials.

Replacing the LED Module:

If the LED module needs to be replaced, follow these steps:

Disconnect the system and open the luminaire.
Refer to the installation instructions for the LED module and follow them.
If the luminaire cover is defective, it must be replaced.
Close the luminaire after replacing the LED module and/or cover.

Spares:

LED Power Supply Unit: DEV-0315/1050i
LED Module 3000 K: LED-1302/930
Reflector: 75 005 081
Mirror: 75 005 090

Instructions for use

Application
Illuminated mirror · Indoor luminaire with velvet black metal housing.
Luminaire with light source shielded to the front and velvet white inside colour of the reflection surface.
Radial light emission 360°.

DIMENSION

Product Description

Luminaire housing made of aluminium, surface Colour velvet black
Inside colour velvet white
Inside synthetic cover, translucent white Mirror made of crystal glass, diameter 550 mm, visible edge polished
4 mounting holes ø 6 mm
Distance 350 mm
2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x 1.5@ Connection terminal 2.5@
Earth conductor connection
2-pole connecting terminal for digital control
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
During DC operation the LED power is reduced to 15 %
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
Conformity mark
Weight: 10.3 kg
This product contains light sources of energy efficiency class(es) D

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

FEATURES

Lamp

Module connected wattage 53.1 W
Luminaire connected wattage 59 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 45 °C

51 222.1 K3

Module designation LED-1302/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 7900 lm
Luminaire luminous flux 2837 lm
Luminaire luminous efficiency 48,1 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Remove the luminaire housing (reflector) from the packaging.
Pass the power connecting cable through the cable entry into the luminaire housing.
Secure the luminaire housing to the installation surface with the fixing materials provided or other suitable materials.
Note position of application of the luminaire housing “arrow down”.
Connect the earth conductor to the earthing screw (1) of the luminaire housing.
Remove the mounting plate with LED unit from its packaging.
Loosen 4 Torx screws (T 20) and remove the central service panel from the LED unit. Loosen earth connection (plug connection) between central service panel and LED unit. Guide wires of the power connecting cable through the rear opening into the LED unit. Place the LED unit over the keyholes onto the four threaded bolts of the luminaire housings and turn it clockwise until it stops.
Tighten the hex nuts M5 over the keyholes. Make the electrical connection to the terminals. Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, DA are provided for digital control purposes.
If these terminals are not assigned, the luminaire will work with full light output. Establish the earth conductor connection of the LED unit to the luminaire housing (plug connector).
Make earth connection (plug connection) from the central service panel to the LED unit again. Place the central service panel back onto the LED unit and fasten using the 4 Torx screws
(T20).
Remove the mirror from its packaging.
Place the rear locking bolts of the mirror fastening onto the 3 elongated recesses of the LED unit.
Turn the mirror clockwise against the resistance until the locking bolts audibly click into their final position.

Cleaning Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Defective luminaire cover must be replaced. Close the luminaire.