AI-Eye VS18200 Fixed Lens Bullet Camera User Guide

June 10, 2024
AI-Eye

AI-Eye VS18200 Fixed Lens Bullet Camera

AI-Eye VS18200 Fixed Lens Bullet Camera

Accessing via Web Browser

Default IP address User name Password
https://192.168.0.11 admin AbAi.Camera1
Appearance Description

The overview of the bullet camera is shown below:
Appearance Description

Packing list
Component Pieces
Camera 1
Drilling sticker 1
Expansion tube 3
Tapping screw 3
Cable
No Item Description
1 LAN/POE Ethernet/POE connection. This interface supports POE.
2 DC 12V+ / DC 12V – Power input interface. DC 12V(9.0V~15.0V)
3 ALARM_OUT
COM Alarm output and COM interfaces. The interface work together to form the

alarm output.
ALARM_IN ALARM_GND| Alarm input interface. There may be multiple alarm interfaces. For a given number of interfaces, n, they are numbered (for example: ALARM_IND, ALARM_IN1, …,ALARM_INn). Each one connects to the ALARM_GND connection to form a single alarm input.
4| AUDIO IN/AUDIO OUT/ AUDIO_GND| Audio input (connect to MIC)/output interface and audio ground interface.

Cable interface

Cable interface

Installation

Note

Make sure the device in the package is in good condition and all the assembly parts are included.

You will need the following:

  • Video surveillance tester

  • Hammer drill (for mounting a camera on the ceilling or wall)

  • PVC insulation tape

  • Phillips screwdriver (Head model:1#and 2#,)

  • RJ – 45 connector crimping tool

  • Measuring tape

  • Claw hammer/for mounting a camera on the ceilling or wall)

  • Cable stripper

  • Waterproof tape

  • Glass cement

  • Utility knife

  • Wiring terminal

Caution

Please do not lift a camera by its cable.
Caution

Front cover of the camera removes
  • Use a Allen key screwdriver to remover the front cover of camera, and rotator the cover to open it. Then, you can see the Reset button and SD card slot.
    Front cover of the camera removes
Reset Button
  • To restore the camera to factory settings and software reboot the camera, you need to press and hold the reset button 5~10 seconds.
  • To restore the camera to factory settings and hardware reboot the camera, you need to press and hold the reset button more than 10 seconds.Micro SD card installation
Micro SD card installation

The SD card slot supports only class 6 or higher Micro SD card. To replace a Micro SD card, the device must be powered off. Otherwise, system exception may occur. When a Micro SD card is used for the first time, log in to the web client of the device and format the Micro SD card. For details, see the Configuration Guide.

Please refer to figure 2.5, insert the memory card to memory card slot on the rear housing of the camera. During SD card installation, you are advised to turn the camera maintenance position upward and insert the SD card into the SD card slot from upon to avoid accidentally dropping the SD card into the camera.
Micro SD card installation

Camera mounting

The suggested mounting height is over 3 meters at least.
The right height and angle of camera is important to ensure image quality.
The figure of the camera is installation requirements for concept and reference only.
Camera mounting

Wall Mounting Installation

Step 1:

Confirm that the cable outlet on the wall is large enough for the pigtails to pass through (size of hole size inserted here). Affix the drilling sticker to the camera installation position and ensure that the center of the sticker matches the cable outlet on the wall.
Wall Mounting Installation

Step 2:

Use a 5mm drill bit to drill four 35mm deep holes in the positions marked by the drilling sticker. Use a hammer to carefully drive the white plastic expansion tubes into the holes.

Step 3:

Connect the external cabling to camera pigtails, insulate the connections (see Cable Connections), and feed the cabling through the cable entry on the wall. Fasten the tapping screws. Make sure the cable outlet at the camera base is installed facing downwards and is sealed with waterproof glue or caulking to prevent water from getting into the camera.
Wall Mounting Installation

Step 4:

Loosen the three Philips head screws and adjust the camera to the required angle. Then re-tighten the screws, and adjust the position of the sunshield.
Wall Mounting Installation

Adjust the angle of the camera. Tighten 3 Philips head screws after adjustment.

Tilt Angle : 90º
Wall Mounting Installation

|

Pan Angle : ± 180º
Wall Mounting Installation

---|---

Rotator Angle : ± 180º

Wall Mounting Installation with Junction Box and Camera

Step 1

Place the junction box on the wall such that the arrows of bottom point to the ground as well as. Then use 4 screws to mount the junction box on to the wall.
Wall Mounting Installation with Junction Box and
Camera

Step 2

Use 3 screws to fix the camera onto the cover of junction box. Then, clip the safety rope of the cover of the junction box to the bottom of the junction box. Thread the cables through the junction and attach them to the camera pigtails. Finally, tighten the screws to fix the cover onto the junction box in place.
Wall Mounting Installation with Junction Box and
Camera

Pole Mounting Installation with Junction Box

Step 1

Open up the 3 hose clamps and thread them through the installation holes on the mounting bracket. Then use 3 hose clamps to affix and install the pole- mount bracket to the pole.
Pole Mounting Installation with Junction Box

Step 2

Place the junction box on the pole-mount bracket such that the arrows of bottom point to the ground as well as. Then use 4 screws to mount the junction box on to the pole-mount bracket.

Step 3

Use 4 screws to fix the camera onto the cover of junction box. Then, clip the safety rope of the cover of the junction box to the bottom of the junction box. Thread the cables through the junction and attach them to the camera pigtails. Finally, tighten the screws to fix the cover onto the junction box in place.

Cable connection

For safety precautions

  • The lightning arrester must be installed and grounded if you install camera outdoor.
  • Strong and weak current cables must be kept at least 5 cm apart from each other. When connecting the cables to the device, take care to avoid connecting strong current cables to weak current interfaces or you will damage your device.
  • The tail of cable must be cut if it cannot pass through the wall, please keep the label on tail of cable. And please make sure to use insulating tape and waterproof tape to insulate and waterproof all tail of cable to avoid short circuits and water leakage.
  • Wrap all pigtail cables in insulated, waterproof, rubber tape to prevent short circuits or water damage.
    For safety precautions

Power cable connection

Connect the power cable to the device.

Ground cable installation

Please connect ground cable of camera to ground

Audio and alarm cable installation

Connect the ground cable to ground the device, and then connect the power cable. If crimp terminals are not used, the wire thickness cannot exceed 1.5mm2 , and the length cannot exceed 25m. If crimp terminals are used, the wire can be up to 0.75mm2 for a 15m length of wiring or up to 1.0mm2 if 20m is required. Longer wiring is not supported. The ground impedance cannot exceed 5 ohms.

Cable waterproof and insulation

Waterproof and insulate all cables including power cables, network cables, and unused pigtails.

  1. Wrap one layer of insulation tape around each cable joint.
  2. Stretch the waterproofing tape evenly to twice its original length. Then apply it for three layers from bottom to top, from top to bottom, and from bottom to top again.
  3. Stretch the insulation tape evenly to twice its original length. Then apply it for three layers from bottom to top, from top to bottom, and from bottom to top again.to up. Finally tie the upper and lower ends with cable ties. Then use cable ties to secure the both ends.
  4. Cover the rest of the cabling in a conduit or with protective waterproof rubber tape. Make a drip loop as shown below to create an artificial lowest point of the cable.
    Cable waterproof and insulation
    Cable waterproof and insulation

Check Item

Check Item Result
All screw fully tightened YES   NO
The camera is securely installed to the mount or wall YES NO
The ambient temperature meets the device specifications. YES NO

Insulation and waterproofing measures have been taken to protect cables installed in humid environments, and the drip loops are in correct positions.| YES NO
The camera can power on normally.| YES  NO
You can access the camera web portal using the IP address you

configured.

| YES  NO
On the camera web portal, you can view live video from camera.| YES NO
You can view the surveillance from camera web pages and the image is clear, as shown in the following figure.| YES NO
In night vision mode, the surveillance is can be viewed clearly.| YES NO

FCC compliance statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals