dormakaba Saffire LX-D and Saffire Evo Deadbolt User Manual

dormakaba Saffire LX-D and Saffire Evo Deadbolt

PART LIST & LOCK DIAGRAM

ITEM NO.|

QTY.

|

DESCRIPTION

---|---|---
1| 1| FRONT LOCK HOUSING ASSEMBLY
2| 1| GASKET FRONT LOCK HOUSING
3| 1| TAIL PIECE
4| 1| INSIDE TRIM ASSEMBLY
5| 1| INSIDE TRIM COVER ASSEMBLY
6| 1| DEADBOLT
7| 1| STRIKER PLATE
8| 1| DUST BOX
9| 1| REINFORCING PLATE
10| 2| PHILLIPS #2, FLAT HEAD WOOD SCREW 8 X 1″ LG
11| 2| PHILLIPS #2, FLAT HEAD WOOD SCREW 8 X 3″ LG
12| 2| PHILLIPS #2, FLAT HEAD SCREW 8-32 X 7/32″ LG
13| 4| PHILLIPS #2, FLAT HEAD SCREW 8-32 X 1/2″ LG
14| 2| PHILLIPS #2, FLAT HEAD WOOD SCREW 8 X 1″ LG
15| 1| PHILLIPE #2, TRUSS HEAD 6-32 X 5/16″ LG
16| 3| PHILLIPS #2, PAN HEAD SCREW 10-24 X 1-1/4″ LG
17| 1| COMMUNICATION HARNESS (OPTIONAL)
18| 1| POWER CABLE
19| 3| AA BATTERY
20| 1| FIRE PLATE
21| 1| BASE PLATE
22| 1| COVER PLATE
23| 3| LOCATING POST
24| 3| PHILLIPS #2 FLAT HEAD SCREW 10-24 X 1.500″ LG
25| 3| PHILLIPS #2 PAN HEAD SCREW 6-32 X 5/16″ LG

WARNING

1. Please read and follow all directions carefully.

2. This lock is not designed to be used on emergency exit doors.

3. Carefully inspect glass, door frame, door, etc. to ensure the recommended procedure will not cause damage.
   dormakaba standard warranty does not cover damages caused by installation.

4. Wear safety glasses when making the holes.

5. All the following operations and testing of the lock are to be done with door open.

TOOLS REQUIRED

• Safety glasses

• 1/2” (13mm) Chisel

• 1/8” (3mm) Drill Bit

• 5/32” (4mm) Drill Bit

• 1” (25mm) Drill Bit or Hole Saw

• 2 1/8” (54mm) Drill Bit or Hole
  Saw

• Drill

• Awl or Center Punch

• Screwdriver, 1/8″ Slotted

• Philips Screwdriver #2

• Adjustable Square

• Tape Measure

• Screwdriver Torx T10

1A – INSTALL STRIKE ON WOOD FRAME

1B – INSTALL STRIKE ON STEEL FRAME

1C – DOOR PREPARATION

A = Backset = 2.3/4″(70mm) or 2 3/8″ (60mm)

1. Determine which template fits your Saffire LX-D lock installation, either 2 3/8″ (60mm) or 2 3/4″ (70mm) backset.
2. Place appropriate template onto door and mark holes.
3. Drill holes as per dimensions on the template. The 1″ (25 mm) hole shall be on the centerline of door thickness.
4. Mortise door edge for dead bolt face plate.
5. Drill 2 1/8″ from both sides of the door to prevent unsightly damage.
   

ADJUST BACKSET OF DEADBOLT

DEADBOLT IS PRE-SET AT 2 ¾” (70mm) BACKSET. PROCEED AS SHOWN TO CHANGE TO 2 ⅜” (60mm) BACKSET, IF REQUIRED.

INSTALL DEADBOLT IN DOOR

ADJUST LOCK HANDING ON OUTSIDE HOUSING ASSEMBLY

1. HOLD INNER CAM IN PLACE, INNER CAM GROOVE ORIENTED AT 12 O’CLOCK.
2. FOR RH LOCK, ROTATE OUTER CAM COUNTERCLOCKWISE UNTIL OUTER CAM GROOVE IS ORIENTED AT 6 O’CLOCK.
3. FOR LH LOCK, ROTATE OUTER CAM CLOCKWISE UNTIL OUTER CAM GROOVE IS ORIENTED AT 12 O’CLOCK.

LEFT HAND (LH)

RIGHT HAND (RH)

ASSEMBLE TAILPIECE

TAILPIECE SHALL BE “SNAP” IN PLACE WITH WIRE RING OPENING ROTATED AT 12 O’CLOCK.

REMOVE INSIDE COVER

ASSEMBLE OUTSIDE HOUSING

8A – INSTALL INSIDE TRIM ASSEMBLY

INSTALL INSIDE TRIM ASSEMBLY (VERTICAL MOUNTING ONLY) – FOR HORIZONTAL MOUNTING SEE 8B – SHEET 3 THEN PROCEED WITH SECTION 9.

8B – INSTALL INSIDE TRIM ASSEMBLY HORIZONTAL MOUNTING OPTION (IF

APPLICABLE)

1. BEFORE TIGHTENING THE SCREWS VERIFY FUNCTIONALITY BY EXTRACTING AND RETRACTING THE DEADBOLT. DEADBOLT SHALL MOVE SMOOTHLY.
2. ALL SCREWS SHALL BE TIGHTENED PROPERLY.
3. CONNECT BATTERIES AFTER TIGHTENING ALL SCREWS AND WIRING W1 & W2.

LH MOUNTING

1. HARNESS SHALL BE PULLED GENTLY THROUGH INSIDE TRIM’S BACKPLATE TO ACCUMULATE ALL EXCESS CABLES WITHIN THE INSIDE TRIM.
   

RH MOUNTING

1. HARNESS SHALL BE PULLED GENTLY THROUGH INSIDE TRIM’S BACKPLATE TO ACCUMULATE ALL EXCESS CABLES WITHIN THE INSIDE TRIM.
   

LOCATING POST AND MOUNTING SCREWS SHALL BE INSTALLED AS SHOWN. LEFT MOUNTING SHOWN. COVER REMOVED FOR CLARITY

INSIDE COVER INSTALLATION

METHOD 1: FOR THIN DOOR, 1.375″ TO 1.50 PLEASE FOLLOW STEP 1, 2A, 3A, 4 & 5.
METHOD 2 (FOR TAILPIECE WITH CHAMFER ONLY): FOR NORMAL DOOR 1.75″ AND
THICKER PLEASE FOLLOW STEP 2B, 3B, 4 & 5. FOR DOOR FROM 1.5″ TO 1.75″ PLEASE USE THE MOST CONVENIENT METHOD, 1 OR 2.

STEP 2A: MOVE THE COVER UPWARD. TAIL PIECE MUST REMAIN ENGAGED IN TURN KNOB.
STEP 3A : ENGAGE COVER’S TAB WITH BACK PLATE HOOK.

STEP 2B: ENGAGE COVER’S TAB IN BACK PLATE’S HOOK. LIFT COVER AS REQUIRED.
STEP 3B : LOWER COVER AND ROTATE AS SHOWN. TAILPIECE WITH CHAMFER SHALL ENGAGE IN RELATED SLOT AUTOMATICALLY.

STEP 4: CLOSE COVER’S BOTTOM.
STEP 5: INSTALL SCREWS.

9B – INSTALL INSIDE TRIM COVER

SEE INSTALLATION DETAIL ON SHEET 2.

COVER PLATE AND INSIDE TRIM ASSEMBLY SHALL BE INSTALLED AS SHOWN WITH 3X SCREWS, ITEM 25.

INTENTIONALLY LEFT BLANK.

ISED non-interference disclaimer

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with ISED RSS-102 radiation exposure limits set forth far an uncontrolled environment. This transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. To avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with minimum distance 20 cm between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance.

REVI SIONS

RE V| ECN| DESCRIPTION| FAIT PAR/ DONE BY| VER. PAR/ VER. BY| DATE
6| CN03611| TITLE WAS: Saffire LX-O & Saffire Evo LX-D lnstallation Guide for door thickness 1 3/.8 to 2 1/8″, BOM ITEM 16 WAS PHILLIPS, 10-24 X 1-1/4″ PANH EAD SCR E W; SH EET 1 ADR E SS E REMOVED| AC| CD| 2022-12–06
7| CN03645| SHEET 1: TITLE WAS Saffire LX Deadbolt & Saffire Evo LX Deadbolt Installation Guide for door thickness 1 3/8″ to 2 1/8•; ITEM 17 WAS MESSENGER CABLE, BALLOON 23 ADDED; SHEET 2 SECTION 2A WAS 2, SECTION 3A WAS 3; SECTION 28 & 38 WITH RELATED VIEW ADDED; SHEET 2 SECTION 5: 12 O’CLOCK WAS 6 O’CLOCK, HARNESS ROUTING REVISED; SHEE T 3: SECTION 8 HARNESS WAS CABLE 2X PLACES; BALLOON 25 ADDED, ROUTING VIEW REMOVE & RELATED NOTE REVISED, SECTION 9B ADDED| AC| CD| 2023-03-13
8| CN04398| SHEET 4 ADDED; INDUSTRY CANADA AND FCC NOTE TRANSFER TO SHEET 4; SHEET 3: VIEW SPACED OUT; SHEET 4: INDUSTRY CANADA &

FCC NOTE REVISED AS PER TUV REQUEST

| AC| CD| 2023-06-29

REVISION TABLE FOR ENGINEERING ONLY DO NOT PRINT THIS SEE

This document containing drawings and information derived therefrom or thereon is confidential and proprietary to dormakaba Canada inc. This document is submitted in confidence and its contents may not be disclosed, reproduced, or revealed in any manner without prior written consent from dormakaba Canada inc. This document will be returned to dormakaba Canada inc. upon demand.

DIMENSIONS
3D FILE GOVERNS ALL UNSPECIFIED DIMENSIONS& GENERAL
GENERAL TOLERANCE, UNLESS OTHERWISE SPECIFIED| DRAWN BY YYYY-MM-DD
A.CHIQUETTE 2018-08-20| dormakaba Canada Inc.
---|---|---
APPROVED BY  YYYY-MM-DD
C.DOUCET 2018-08-21| TITLE
ATERIAL N/A| | DWG NO PK3705| REVISION 8
FINISH N/A| PART NO
PK3705| SHEET / FEUIL

1/5

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>