gorenje R2-01-1 Remote Control User Manual
- June 4, 2024
- Gorenje
Table of Contents
gorenje R2-01-1 Remote Control
Remote controller
The remote controller transmits signals to the system.
-
MODE
Press this button to select the operation mode. -
TEMP 2
Used to adjust the room temperature and the timer, also real time. -
Hi-NANO
Used to set or cancel HI-NANO operation. -
POWER
The appliance will be started when it is energized or will be stopped when it is in operation, if you press this button. -
FAN SPEED
Used to select fan speed in sequence auto, higher, high, medium, low and lower. -
SUPER
Used to start or stop the fast cooling/heating.
(Fast cooling operates at high fan speed with 16’C(61’F) set temp automatically ; Fast heating operates at auto fan speed with 30″C(86’F) set temp automatically -
!SWING
Used to stop or start vertical adjustment louver swinging and set the desired up/ down airflow direction. -
SLEEP
Used to set or cancel Sleep Mode operation. -
QUIET
Used to set or cancel Quiet Mode operation. -
SWING
Used to stop or start Horizontal adjustment louver swinging and set the desired left right airflow direction. -
ON/OFF TIMER
Used to set or cancel the timer operation. -
SMART(invalid for multi system)
Used to enter fuzzy logic operation directly when f the unit is on .When the Air conditioner and Remote controller are in standby, and the mode of remote controller is in Cooling or Dry, press this button for about 5 seconds to enter the auto-clean mode and then the indicator “.,;,.” will display on LCD . Press SMART or POWER or MODE button will escape from auto-clean mode, and then the indicator”.!;,.” will disappeared/After the clean process finish, the air conditioner will return to Cooling or Dry as preset, while the indicator’.,;,.” on remote controller will display for about 30 mins) -
DIMMER
When you press this button, all the display of indoor unit will be closed. Press any button to resume display. -
CLOCK
Used to set the current time. -
ECONOMY
Used to set or cancel Economy Mode operation. -
FEEL
Press to set IFEEL Mode operation. In IFEEL mode, the Air Conditioner operates basis temperature sensor fitted in remote instead of machine, Advice to use IFEEL mode and the remote put where the indoor unit receive signal easily. Press this button above 5 seconds, start or stop IFEEL mode.
Note:
Each mode and relevant function will be further specified in following
pages.
How to Insert the Batteries
-
Pry open the battery cover according to the arrow direction.
-
Insert new batteries making sure that the ( +) and (-) of battery are matched correctly.
-
Reattach the cover by pressing it back into position.
Note:
Use 2 LR03 AAA(1.5volt) batteries. Do not use rechargeable batteries. Replace
batteries with new ones of the same type when the display becomes dim.
Storage and Tips for Using the Remote Controller
The remote controller may be stored mounted on a wall with a holder.
Note: The remote controller holder is an optional part.
Note: The shape may differ from that of the remote controller
holder
How to Use
To operate the room air conditioner, aim the remote controller to the signal
receptor. The remote controller will operate the air conditioner at a distance
of up to 7m when pointing at signal receptor of indoor unit.
CAUTIONS
For appropriate signal transmission between remote controller and indoor unit,
keep the signal receiver away from the following items:
- Direct sunlight or other strong lights or heat
- Flat panel television screen or other electrical appliances that react to the remote controller
Additionally, the air conditioner will not operate if curtains, doors or other
materials block the signals from the remote controller to the indoor unit. If
the signal may not be transmitted properly, either move these materials or
consult your local dealer.
Operation instructions
Operation modes
Selecting mode
-
Press MODE button once by once
-
Result: The operation modes changed in sequence:
-
Heating mode is NOT available for cooling only air conditioner.
FAN mode
-
Press fan speed button once by once
-
Result: The fan speed is changed in sequence:
-
At “FAN ONLY mode, only “Auto• is not available.
-
At “DRr mode, Fan speed is set at “AUTO” automatically, “FAN SPEED” button is ineffective in this Some models, such as case. commercial air conditioner products, only have the third gear speed.
Setting temperature
- Press high temp button once
- Result: Raise temperature setting by 1 ·c or 1 ° F
- Press low temp button once
- Result : Lower temperature setting by 1 ·c or 1 ° F
Turning on
- Press (!) button.
- Result : The RUN indicator of the indoor unit lights up.
- SWING, SMART, SUPER, QUIET, TIMER, ECONOMY, /FEEL, DIMMER, CLOCK, SLEEP and 8°C HEAT operation modes will be specified in the following pages.
- Changing modes during operation, sometimes the unit does not response at once. Wait 3 minutes.
- During heating operation, air flow is not discharged at the beginning. After 2-5 minutes, the air flow will be discharged until temperature of indoor heat exchanger rises.
- Wait 3 minutes before restarting the appliance.
Airflow direction control
Vertical airflow(Horizontal airflow) is automatically adjusted to a certain
angle in accordance with the operation mode after turning on the unit.
The direction of
airflow can be also adjusted to your own requirement by pressing the .swings
buttons of the remote controller.
*Heating mode is only available for heat pump models.
Vertical airflow control (with the remote controller)
Using remote controller to set various angles of flow or specific angle as you
like.
-
Press swing button once.
-
Result: The vertical adjustment louver will swing up and down automatically.
-
Press swing button again .
-
Result: The louvers swing to a suitable angle as desired.
Horizontal airflow control (with the remote controller)
Using remote controller to set various angles of flow or specific angle as
you like.
- Press swings button once.
- Result: The horizontal adjustment louver will swing left and right automatically.
- Press swings button again .
- Result : The louvers swing to a suitable angle as desired.
SMART mode(invalid for multi system)
How to set SMART mode?
- Press the button.
- Result: Enters SMART mode(fuzzy logic operation) directly only when the unit is on . Temperature and fan speed are automatically set based on the actual room temperature.
For the split-
type models, such as wall-mounted air conditioners and some floor-standing air
conditioners, their operation mode and set temperature should be determined
based on the indoor temperature.
Operation mode and temperature are determined by Indoor temperature
Heat pump models
Indoor temperature
| Operation mode|
Target temperature
---|---|---
21°C(?0°F) or below
| HEATING| 22°C(?2°F)
21·c-23·c(10°F-?3°F)| FAN ONLY|
23·c-25·c(73°F-79°F)
| DRY| Room temperature decrease 2°C(2°F) after operate for 3 minutes
Over 26°C(79°F)| COOLING|
26°C(79°F)
Cooling only models
Indoor temperature
| Operation mode|
Target temperature
---|---|---
23°C(73°F) or below
| FAN ONLY|
23·c-25·c(73°F-79°F)| DRY|
Room temperature decrease 2°C(2°F) after operate for 3 minutes
Over 26°C(79°F)
| COOLING|
26°C(79°F)
For the split-type models, such as wall-mounted air conditioners and some
floor-standing air conditioners, their operation mode and set temperature
should be determined based on the indoor temperature.
The operation mode Is determined by the difference between the Indoor
temperature and set temperature.
Heat pump models
Indoor temperature
| Operation mode|
Target temperature
---|---|---
Below T-3″C (3°F)
| HEATING| T
T-3″Ce:;Tindoor e:;T+3°C (3°F)| FAN ONLY|
T
Over T+3°C (3°F)
| COOLING|
T
Cooling only models
Indoor temperature
| Operation mode|
Target temperature
---|---|---
T+3″C (3°F) or below
| FAN ONLY| T
Over T+3·c (3°F)| COOLING|
T
- SMART button is ineffective in SUPER mode.
- ECONOMY button is ineffective in SMART mode.
- Press MODE button cancel SMART mode.
Note: Temperature, airflow and direction are controlled automatically in SMART mode. However. For the on/off. you can choose from -2 to 2 (for some models you can choose from -7 to 7), for the inverter you can choose from -7 to 7. if you still feel uncomfortable.
What you can do in SMART mode?
Your feeling
| Button|
Adjust
---|---|---
Uncomfortable because of unsuitable air flow volume.| 
| Indoor fan speed alternates among Auto, Higher, High
Medium, Low and Lower each time this button is pressed.
Uncomfortable because of unsuitable flow direction.| 
| Press it once, the vertical adjustment
louver(horizontal adjustment louver) swings to change vertical airflow
direction(horizontal airflow direction). Press ii again, swings stops.
How to cancel the SMART mode?
- Press the mode button.
- Result: The SMART mode will be cancelled.
SUPER mode
- SUPER mode is used to start or stop fast cooling or heating only when the unit is on.
- SUPER mode can be set when the appliance is in operation or energized.
- In SUPER mode, you can set temperature, airflow direction or timer
How to set SUPER mode?
-
Press super button at the cool, dry and fan only mode.
-
Result: At high fan speed ,the set temperature
-
Press super button at the heat mode.
-
Result:- At auto fan speed ,the set temperature automatically to 30’C(86’F).
How to cancel SUPER mode?
-
Press SUPER, MODE, FAN SPEED, ON/OFF, QUIET or SLEEP button.
-
Result: The display return to the original mode.
-
Escape from SUPER mode.
Note:
SMART button is not available in SUPER mode. ECONOMY button is not available
in SUPER mode.
The Appliance will continue working in SUPER mode for 15 minutes. if you don’t
escape from it by pressing any of the buttons mentioned above.
QUIET mode
In fan this speed. mode, This the air mode is conditioner only will available
work for with inverter low noise models. performance by low compressor
frequency and low
fan speed .This mode is only available for inverter models .
Note:
Press MODE, FAN SPEED, SMART, SUPER, ECONOMY or ON/OFF button cancel QUIET
mode.
Operation instructions
Timer mode
It is convenient to set the timer on with ON TIMER buttons when you go out in
the morning to achieve a comfortable room temperature at the time you get
home. You can also set timer off at night to enjoy a good sleep.
How to set ON TIMER ?
-
Press button.
Result: “12:00 ON” flashes on the LCD.
-
Press the A or V button.
Result:
Once to increase or decrease the time setting by 1 minute. One and a half seconds to increase or decrease the time setting by 10 minute. For a longer time to increase or decrease the time by 1 hour. -
When your desired time displayed on LCD, press the ON TIMER button and confirm it.
Result:
A “beep” can be heard. “ON” stops flashing. The TIMER indicator on the indoor unit lights up.(invalid for some models)
-
After the set timer displayed for 5 seconds the clock will be displayed on the LCD of the remote controller instead of set timer.
How to cancel ON TIMER ?
Press the button.
Result:
A “beep” can be heard and the indicator disappears, the time on mode has been
canceled.
Note:
It is similar to set OFF TIMER , you can make the appliance switch off
automatically at your desired time, the difference is you need to press the
ON/OFF TIMER button for about 5 seconds to start the OFF TIMER.
ECONOMY mode
In this mode, the air conditioner will bring you energy saving performance by
lower running currency.
- ECONOMY button is ineffective in SUPER and SMART mode.
- Press ON/OFF, MODE, TEMP/\, TEMP V, FAN SPEED, SLEEP,QUIET or ECONOMY button cancel ECONOMY mode. ****
IFEEL mode
The temperature sensor built in remote controller is activated it can sense
.Its surroundings temperature and transmit the signal back the unit ,the unit
can adjust the temperature so as to provide maximum comfort.
How to set /FEEL mode ?
Press the button for about 5 seconds once.
Result: the The IFEEL transmit function signal in will the be display
started. will appear,
Note:
The default setting is /FEEL inactiving.
How to cancel /FEEL mode?
Press the button for about 5 seconds once again.
Result: IFEEL function will be shunted off.
DIMMER button
How to set the DIMMER ?
Press the DIMMER button to turn off the light and the display in the unit.
Note:
When the light is off, receive signal will turn on the light again.
CLOCK button
- How to adjust the real time?
-
Press button for about 5 seconds once.
Result: The time flashes on the LCD.
-
Press A and V buttons.
Result: Once to increase or decrease the time setting by 1 minute. One and a half seconds to increase or decrease the time setting by 10 minute For a longer time to increase or decrease the time by 1 hour. -
Press button once again.
Result: The real time is set.
SLEEP mode
SLEEP mode can be set in COOLING ,HEATING or DRYING mode. This function gives
you a more comfortable environment for sleep.
- The appliance will stop operation automatically after operating for 8 hours.
- Fan speed is automatically set at low speed.
How to set SLEEP mode ?
Each time button is pressed.
Result: SLEEP function will be started. 
SLEEP mode:
- Set temperature will rise by 2″C(2’F) at most if the appliance operates in cooling mode for 2 hours constantly, then keeps steady.
- Set temperature will decrease by 2″C(2’F) at most if the appliance operates in heating mode for 2 hours constantly, then keeps steady.
Note: In cooling mode, if room temperature is 26°C (79°F) or above, set temperature will not change.
- Heating is NOT available for cooling only air conditioner.
How to cancel SLEEP mode ?
Press SUPER , SMART, MODE, SLEEP, ON/OFF, ECONOMY or FAN SPEED button
Result:
The display return to the original mode. Escape from SLEEP mode.
8°C HEAT mode(optional)
How to set 8°C HEAT?
In HEATING mode, Press and buttons together for 2 seconds to start B’C HEAT
mode. In B’C HEAT mode, the fan speed is set at “AUTO” automatically. The icon
If will appear on the LCD. If pressing any button, other than ON TIMER, OFF
TIMER, CLOCK, DIMMER, IFEEL and SWING, B’C HEAT function will be turned off.
And the icon If will disappear.
Note:
In 8°C HEAT mode, the default temperature is set 8 C. 8 ° C HEAT mode can be
set only when the air conditioner works in HEATING mode.
HI-NANO mode
When the Remote controller is on, in any mode, press HI-NANO button can set or
cancel the HI-NANO mode, then the icon “E)l” will appear or disappear on the
LCD
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>