BEGA 34022.1 LED Ceiling and Wall Luminaire Instruction Manual

BEGA 34022.1 LED Ceiling and Wall Luminaire

Product Information

The product is a luminaire that consists of a lamp module with a connected wattage of 67.2 W and a luminaire connected wattage of 76.4 W. The rated temperature for the product is 25°C, and it can operate in an ambient temperature range of 40°C to 80°C. The module designation is 34 022.1 K3, and it has a colour temperature of 3000 K. The colour rendering index (CRI) is greater than 90. The module has a luminous flux of 11310 lm, while the luminaire has a luminous flux of 6151 lm and a luminaire luminous efficiency of 80.5 lm/W.

Product Usage Instructions

1. Safety: The installation and operation of this luminaire should be carried out in accordance with national safety regulations. Only a qualified electrician should perform the installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. Any subsequent modifications should be done by a qualified person who will be considered the manufacturer.
2. Overvoltage Protection: The electronic components in the luminaire are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website at www.bega.com.
3. Notice Prior to Installation:
   • Ensure that the ceiling or wall has sufficient load capacity to support the luminaire.
   • Consider the position of cable entries for the electrical connection (refer to the provided sketch).
   • Drill six mounting points in the mounting surface. Note that general fixing material may not be suitable for all applications. Check for approval from building supervision.
4. Installation:
   • Remove the luminaire from its packaging and place it on a soft surface.
   • Open the luminaire by using a hex key (size 3) to turn the ceiling bracket on the housing ring a quarter turn to the left.
   • Fully open the ceiling bracket by slightly tilting the torsion spring back.
   • Carefully raise the installation box and disconnect the LED connector.
   • Using a socket wrench (size 8) or a ratchet, unscrew the three nuts above the hinge until the end of the thread.
   • Pull the safety clamp forward and remove the installation box upwards.
   • Reconnect the LED plug connectors to the left and right of the ceiling bracket.
   • Close the luminaire until it reaches the spring arrester.
   • Insert an Allen wrench (size 3) into the locking system at the housing ring and turn it against the spring resistance to the left.
   • Press the luminaire into its final position, ensuring that the countersunk socket screw is properly locked in place.
5. Replacement Parts:
   • Ersatzglas (Replacement glass)
   • LED-Netzteil (LED power supply)
   • LED-Modul 3000 K (LED module with a colour temperature of 3000 K)
   • Dichtung LED-Einrichtung (Seal for LED device)
   • Dichtung Glas (Seal for glass)

DIMENSION

Application

Large-area luminaire · indoor luminaire with high light power and high uniform light distribution.

Product description

• Luminaire housing made of aluminium
• Finish colour white
• Crystal glass, inside white Silicone gasket
• 2 cable entries for through-wiring for mains cable up to ø 11 mm max. 5 x 1.5@ Connection terminal 2.5@
• Earth conductor connection
• 2-pole connecting terminal for digital control
• LED power supply unit
• 220-240 V x 0/50-60 Hz
• DC 176-276 V
• During DC operation the LED power is reduced to 15 %
• DALI-controllable
• Number of DALI addresses: 1
• Basic insulation is provided between the mains and control cables
• BEGA Thermal Control®
• Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
• Safety class I
• r – Safety mark
• c  – Conformity mark
• Weight: 11.1 kg
• This product contains light sources of energy efficiency class(es) C

PRODUCT SPECIFICATION

• Lamp
  • Module connected wattage 67.2 W
  • Luminaire connected wattage 76.4 W
  • Rated temperature ta = 25 °C
  • Ambient temperature ta max = 40 °C
• 34 022.1 K3
  • Module designation 6x LED-0729/930
  • Colour temperature 3000 K
  • Colour rendering index CRI > 90
  • Module luminous flux 11310 lm
  • Luminaire luminous flux 6151 lm
  • Luminaire luminous efficiency 80,5 lm / W

Safety

• The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Notice prior to installation:

• For fixing the luminaire please consider sufficient load capacity of ceiling or wall.
• For the electrical connection the position of the cable entries must be considered (see sketch). Drill 6 mounting points in the mounting surface. General fixing material may not be suitable for all applications.
• Note approval of building supervision.

Installation

• Remove the luminaire from its packaging and lay it out on a soft surface.
• Open the luminaire:
• Use a hex key (size 3) to open the ceiling bracket on the housing ring with a quarter turn to the left.
• Open the ceiling bracket fully by slightly tilting the torsion spring back a little.

• Raise the installation box carefully and disconnect the LED connector.
• Unscrew the 3 nuts above the hinge until the end of thread using a socket wrench (size 8) or a ratchet.
• Pull the safety clamp forward and take off the installation box upwards.

• Note position of application “arrow down” when installed at the wall; the safety clamp has to show to the top!

• Fix installation box with enclosed or any other suitable fixing material onto the mounting surface.

• Lead mains supply cable through one of the

• 2 cable entries into the installation box.

• Make earth connection and electrical connection to terminals.

• For digital control please use the connecting terminal DA, DA.

• In case this terminal is not used the luminaire will be operated at full light output.

• Pick up the luminaire and insert the hinge laterally to the arrester.

• Screw the three hex-nuts sittings above the hinge tightly – torque 3.4 Nm.
  Attention:

  • The luminaire is only then securely attached to the ceiling bracket when all three nuts are tightened!
  • Reconnect the LED plug connectors to the left and right of the ceiling bracket.
  • Close luminaire as far as to the spring arrester. Insert an Allen wrench (size 3) into the locking system at the housing ring and turn it against the spring resistance to the left.
  • Press the luminaire into the final position and observe that the countersunk socket screw is properly locked in the initial position.

Deinstallation

• Disconnect the electrical installation.
  ATTENTION:
  Once the closure system is unlocked, the weight of the luminaire must be supported!To open the luminaire unsrew the locking system of the installation box by turning it with an Allen key (no. 3) for a quarter-turn to the left. Support the weight of the luminaire until the torsion spring engages.

• For the complete opening of the installation box incline the torsion spring backwards out of the arrester and swing out the luminaire. Disconnect the LED connectors to the left and right side.

• Unscrew the 3 nuts above the hinge until the end of thread using a socket wrench (size 8) or a ratchet.

• Pull the safety clamp forward and take off the luminaire.

• Place luminaire on repository.

Relamping · Maintenance

• Deinstall luminaire according to instructions. Open luminaire and remove LED-unit. Disassemble LED module.

• Assemble LED replacement module.

• Note installation instructions of the  LED module.

• Reassemble LED-unit
  Check the gasket and replace, if necessary. Clean glass and luminaire regularly with solvent-free cleansers from dirt.

• Close the luminaire.

• Make sure that gasket is positioned correctly. A broken glass must be replaced.

Spares

• Spare glass 14 001 055 RG
• LED power supply unit DEV -0214/2100i
• LED module 3000 K LED -0729/930
• Gasket LED unit 81 000 295
• Gasket glass 81 000 306

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>