iottie iTap 3 Magnetic Dash and Windshield Mount User Manual
- July 27, 2024
- iOttie
Table of Contents
iottie iTap 3 Magnetic Dash and Windshield Mount
Product Information
At a Glance
- Magnetic Mounting Face
- Rotating Ball Joint
- Telescopic Arm
- Pivot Knob
| Specifications Item | Length | Width | Height | Weight |
|---|---|---|---|---|
| Specification | 5.3 inches | 2.5 inches | 2.7 inches | 4.5 oz |
*Telescopic arm extends from 4 inches to 6 inches.
Installation Product Assembly
- Connect the mount cradle to the ball joint.
- Tighten the cradle knob.
Attaching the Dash Mount
Option A – Dashboard or Flat Surface Installation
- Choose a flat area on the vehicle’s dashboard and wipe any dust or debris from the surface.
- Peel off the film on the dashboard pad and evenly press onto the desired installation location. Wait at least 20 minutes before attaching the mount.
- Remove the plastic cover from the suction cup and firmly press the mount onto the dashboard pad.
- Push down the locking lever to engage suction.
Option B – Windshield Installation
- Choose a location on the windshield and wipe any dust or debris from the surface.
- Peel off the protective film on the suction cup and press firmly onto the windshield.
- Push down the locking lever to engage suction.
To reuse the suction cup, simply rinse under warm water and let air dry to restore tacky suction.
Attaching the Magnetic Ring Adapter
For devices and cases that are not Qi2 or MagSafe compatible, attach the
included magnetic ring adapter to the back of your phone or phone case to
enable compatibility with the iTap 3.
Note: Not designed for use with metal, glass, or textured phone cases, or phones with built-in wallets or grips.
- Clean the back of your phone or phone case with the wet wipe, then use the dry wipe.
- Position the alignment guide so that the opening is in the center of your phone or case.
FAQ
-
Q: Can I reuse the dashboard pad after removal?
A: The dashboard pad is mounted with a semipermanent adhesive tape. Once removed, it cannot be re-mounted. When removing the dashboard pad, please use caution. We recommend removing slowly from the edge to avoid damage. -
Q: What devices are compatible with iTap 3?
A: iTap 3 products are compatible with MagSafe series iPhones and cases. The included magnetic adapter ring can be attached to the back of all other smartphones and smartphone cases for universal compatibility. -
Q: How do I clean and reuse the suction cup?
A: To reuse the suction cup, simply rinse under warm water and let air dry to restore tacky suction.
iTap 3
Magnetic Dash & Windshield Mount
User Manual
Index
For optimal mounting, please follow the details instructions within this
manual when using the iTap 3 Magnetic Dash & Windshield Mount. iOttie is not
liable for possible damages due to product misuse.
Product Information
At a Glance
Device Compatibility
iTap 3 products are compatible with MagSafe series iPhones and cases. The
included magnetic adapter ring can be attached to the back of all other
smartphones and smartphone cases for universal compatibility.
Product Specifications
| Item | Specification |
|---|---|
| Length | 5.3″ |
| Width | 2.5″ |
| Height | 2.7″ |
| Weight | 4.5 oz |
*Telescopic arm extends from 4 inches to 6 inches.
Installation
Product Assembly
- Connect the mount cradle to the ball joint.
- Tighten the cradle knob.
Attaching the Dash Mount
Choose an installation method: dashboard/flat surface (A) or windshield (B).
Option A
Dashboard or Flat Surface Installation
Choose a flat area on the vehicle’s dashboard and wipe any dust or debris from
the surface.
*If your vehicle has a leather dashboard we recommend windshield mounting to avoid damaging your dash.
- Peel off the film on the dashboard pad and evenly press onto the desired installation location. Wait at least 20 minutes before attaching the mount.
- Remove the plastic cover from the suction cup and firmly press the mount onto the dashboard pad.
- Push down the locking lever to engage suction.
The dashboard pad is mounted with a semi-permanent adhesive tape. Once
removed, it cannot be re-mounted.
When mounting, it is recommended that the surface and product be above 65°F.
When removing the dashboard pad, please use caution. We recommend removing
slowly from the edge to avoid damage.
Option B
Windshield Installation
Choose a location on the windshield and wipe any dust or debris from the
surface.
*The dashboard pad should not be used for windshield mounting.
- Peel off the protective film on the suction cup and press firmly onto the windshield.
- Push down the locking lever to engage suction.
To reuse the suction cup, simply rinse under warm water and let air dry to restore tacky suction.
Attaching the Magnetic Ring Adapter
For devices and cases that are not Qi2 or MagSafe compatible, please attach
the included magnetic ring adapter to the back of your phone or phone case to
enable compatibility with the iTap 3.
Not designed for use with metal, glass, or textured phone cases, or phones with built-in wallets or grips.
- Clean the back of your phone or phone case with the wet wipe, then use the dry wipe.
- Position the alignment guide so that the opening is in the center of your phone or case.
- Remove the protective film from the magnetic ring.
- Carefully place the magnetic ring inside the opening on the alignment guide and press fimrly. Wait at least one hour before using.
*Once attached, the ring can be removed, but not repositioned.
Mounting Your Phone
Simply tap your phone against the mount and the magnets will hold it in place.
You are now ready to start driving.
The iTap3 Dashboard & Windshield Mount is backed by a 2 year warranty.
MagSafe Compatible
Only compatible with MagSafe iPhone series and cases.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>