BEGA 50653.1 LED Ceiling and Wall Luminaire for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
50 653.1
Ceiling and wall luminaire for indoor use
Instructions for use
50653.1 LED Ceiling and Wall Luminaire for Indoor Use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass,
satin matt and metal housing, for all lighting tasks.
They are ideal for places where a soft and uniform lighting distribution is
required.
Product description
Metal housing, finish Colour white Hand-blown opal glass, satin matt, with
sliding-bolt closure 2 mounting holes ø 5.5 mm Distance apart 200 mm 2 cable
entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@
Connecting terminal 2.5@ with plug connection Earth conductor connection LED
power supply unit 220-240 V /50-60 Hz DC 176-280 V BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components Safety
class I Protection class IP 44 Protected against granular foreign bodies ≥ 1
mm and splash water Impact strength IK05 Protection against mechanical impacts
< 0.7 joule
– Safety mark
– Conformity mark
Weight: 3.1 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
Module connected wattage| 16 W
Luminaire connected wattage| 18.5 W
Rated temperature| ta = 25 °C
Ambient temperature| ta max = 30 °C
50 653.1 K3
Module designation| LED-0569/930
Colour temperature| 3000 K
Colour rendering index| CRI > 90
Module luminous flux| 2440 lm
Luminaire luminous flux | 1333 lm
Luminaire luminous efficiency | 72,1 lm / W
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Disassemble LED module.
Loosen LED-connection and earth connection (plug connection).
Dismantle the mains supply cable max. 80 mm.
Lead mains supply cable through the cable entry into the luminaire housing.
Fix the luminaire housing with enclosed or any other suitable fixing material
onto the mounting surface.
It is imperative to use the enclosed gaskets.
Make earth and electrical connection to the terminal.
Make earth connection between LED module and luminaire housing (plug
connection).
Push LED-plugs into couplers as far as it will go.
Assemble LED module.
Tighten the screws evenly (max. 0,8 Nm).
Please observe that the LED module is not damaged mechanically.
Insert the opal glass into the luminaire housing with sliding bolt glass
closure and turn the glass clockwise up to the stop.
Place glass to the luminaire housing and observe that the holding spring bolts
fit into the notches of the glass.
Turn the glass clockwise until it is locked.
Thus, you reach a safe and vibration-resistant holding of the glass.
To release the glass from the luminaire housing, turn it counter-clockwise.
Replacement of the LED module. Maintenance
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect the system.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Clean glass and luminaire regularly with solvent-free cleansers from dirt.
Please follow the installation instructions for the LED module.
Screw in glass by turning it clockwise as far as it will go.
A broken glass must be replaced.
Spares
Spare glass| 11 002 770 .0R G
LED power supply unit| DEV-0150/700
LED module 3000 K| LED-0569/930
Technical amendments reserved
BEGA Gantenbrink-Leuchten KG · Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>