PLANET Technology XST-705A Smart Media Converter User Manual
- June 13, 2024
- Planet Technology
Table of Contents
PLANET Technology XST-705A Smart Media Converter
Product Information
The PLANET 10G Smart Media Converter (XST-705A) is a versatile networking device that allows for the conversion between different network interfaces and speeds. It features a 10G/5G/2.5G/1G/100BASE-T RJ45 interface with auto MDI/MDI-X function and a 10GBASE-X SFP+ slot. The converter is compliant with various Ethernet standards, supports auto-negotiation, and offers full-duplex mode for different speeds. It also includes features such as back pressure and IEEE 802.3x pause frame flow control to prevent packet loss. The product supports jumbo frame sizes,automatic address learning, and address aging.
The XST-705A comes in a compact-sized metal case with a wall-mount design. It has a 5V DC, 2A power supply and supports 6000 VDC Ethernet ESD protection. The operating temperature range is from 0 to 50 degrees Celsius. The converter can be used in conjunction with PLANET’s Managed Media Converter Chassis series (MC-1610MR/MC-1610MR48) and offers plug-and-play installation.
Product Usage Instructions
- Open the package of the Smart Media Converter and carefully unpack it.
- Verify that the following items are included in the package:
- XST-705A Smart Media Converter x 1
- User’s Manual x 1
- Power Adapter (5V, 2A) x 1
- SFP Dust Cap x 1
If any item is missing or damaged, contact your dealer immediately. If possible, retain the carton and original packing materials for potential return or repair.
- Choose the appropriate network cable based on the desiredspeed:
- For 10G/5G/2.5G/1G/100M BASE-T connections, use Cat 6A/Cat 7 cables for 10G, Cat 6/Cat 6A/Cat 7 cables for 5G, and Cat 5e/Cat6/Cat 6A/Cat 7 cables for 1G/2.5G/100M.
- For 10GBASE-LR/SR/BX connections, use 50/125m or 62.5/125m multi-mode fiber optic cables for distances up to 300m, or use 9/125m single-mode fiber optic cables for distances up to 60km.
- Connect the appropriate network cable to the corresponding port on the Smart Media Converter:
- For copper connections, use the 10G/5G/2.5G/1G/100BASE-T RJ45 interface.
- For fiber optic connections, use the 10GBASE-X SFP+ slot.
- Connect the other end of the network cable to the corresponding device or network infrastructure.
- Connect the Power Adapter (5V, 2A) to the power input port on the Smart Media Converter.
- Plug the Power Adapter into a power outlet.
- The LED indicators on the Smart Media Converter will indicate the status of the connections and power.
- The Smart Media Converter is now ready for use. Refer to the User’s Manual for any further configuration or troubleshooting instructions.
Package Contents
Thank you for purchasing PLANET 10G Smart Media Converter. In the following sections, unless specified, the term “Smart Media Converter” mentioned in this manual refers to the XST-705A. Open the box of the Smart Media Converter and carefully unpack it. The box should contain the following items
| XST-705A Smart Media Converter x 1 | User’s Manual x 1 |
|---|
|
Power Adapter (5V, 2A) x 1| SFP Dust Cap x 1
|
If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
Product Features
XST-705A Physical Port
- One 10G/5G/2.5G/1G/100BASE-T RJ45 interface with auto MDI/ MDI-X function
- One 10GBASE-X SFP+ slot
Layer 2 Features
- IEEE 802.3u/802.3ab/802.3bz/802.3ae Ethernet standard compliant
- Supports auto-negotiation and 100Mbps half/full duplex and 1/2.5/5/10Gbps full duplex mode
- Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
- 16K jumbo frame size support
- Automatic address learning and address aging
Case and Installation
- External 5V DC, 2A power supply
- Wall-mount design
- Supports 6000 VDC Ethernet ESD protection
- 100 meters over Cat 6A/Cat7 at 10Gbps
- 0 to 50 degrees C operating temperature
- Co-works with PLANET’s 19” Managed Media Converter Chassis series (MC-1610MR/MC-1610MR48)
- Plug and Play installation
Product Specifications
| Model | XST-705A |
|---|
Hardware Specifications
Copper Interface
| 1 x 10G/5G/2.5G/1G/100BASE-T RJ45
Auto-MDI/MDI-X, auto-negotiation
Fiber Optic Interface|
1 x 10GBASE-X R SFP+ slot
LED
| System:
PWR (Green)
10G/5G/2.5G/1G/100 BASE-T RJ45
Interfaces:
1G/10G LNK (Amber)
5G/2.5G/100M LNK (Green)
ESD Protection| 6KV DC
Enclosure| Compact-sized metal case
Installation| Desktop or wall mounting
Dimensions (W x D x H)|
93.8 x 80.75 x 26.4mm
Weight| 182g (device only)
Power Requirements|
5V DC, 2A max.
Power Consumption|
3.8 watts/13 BTU per hour (max.)
Converter Specifications
Switch Processing Scheme|
Store and Forward
Flow Control
| Copper Interface:
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Fabric| 20Gbps
Jumbo Frame| 16K
Network Cables
|
10G/5G/2.5G/1G/100M BASE-T:
10G–Cat 6A/Cat 7
5G–Cat 6/Cat 6A/Cat 7
1G/2.5G–Cat 5e/Cat 6/Cat 6A/Cat 7 100M–Cat 5/Cat 5e/Cat 6/Cat 6A/Cat 7
Cat 5/5e/6/6A/7 UTP cable (100 meters, max.) EIA/TIA-568 100-ohm STP (100 meters, max.)
10GBASE-LR/SR/BX:
50/125μm or 62.5/125μm multi-mode fiber
optic cable, up to 300m
9/125μm single-mode fiber optic cable, up to
60km
Standards Conformance
Regulatory Compliance|
FCC Part 15 Class A, CE
Operating environment|
0 ~ 50 degrees C
Storage Environment|
-10 ~ 70 degrees C
Operating Humidity|
5 ~ 95%, relative humidity (non-condensing)
Storage Humidity| 5 ~ 95%, relative humidity (non-condensing)
Standards Compliance
| IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3bz 2.5G/5GBASE-T IEEE 802.3an 10GBASE-T
IEEE 802.3ae 10Gbps Ethernet
IEEE 802.3x full-duplex flow control (Copper Port)
Physical Dimensions
- XST-705A dimensions (W x D x H): 93.8 x 80.75 x 26.4mm
Converter Front Panel and LED Indicators
The front panel of the Smart Media Converter shows below:
System
| LED | Color | Function |
|---|
PWR
| ****
Green
| Lit: Power is active
Off: Power is inactive
Per 10G/5G/2.5G/1G/100BASE-T Port
| LED | Color | Function |
|---|
10/2.5/1G
| ****
Green
| Lit: To indicate that the port is operating at 2.5Gbps.
Amber
| Lit: To indicate that the port is operating at 10/1Gbps.
5G/100M
| ****
Green
| Lit: To indicate that the port is operating at 5Gbps/100Mbps.
Rear Panel
The rear panel of the XST-705A consists of one DC jack, which accepts input
power with 5V DC, 2A.
Power Information:
The central pole of the Smart Media Converter’s power jacks measures 2.5mm
wide that requires +5VDC power input. It conforms to the bundled AC-DC adapter
and PLANET’s media chassis. Should you have the issue of power connection,
please contact your local sales representative.
Please keep the AC-DC adapter as a spare part when the XST-705A is installed
in a media chassis.
- 2.5mm
- Width of DC Receptacle: 2.5mm
- +5V for each slot
DC receptacle is 2.5mm wide that matches the central pole; the width of the Smart Media Converter DC jack also measures 2.5mm. Warning: Do not install any improper unit
The device is a power-required device, meaning it will not work till it is powered. If your networks should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime. In some areas, installing a surge suppression device may also help to protect your Smart Media Converter from being damaged by unregulated surge or current to the converter or the power adapter.
Installation
This section describes the functionalities of the Smart Media Converter’s components and guides you to how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing.
Stand-alone Installation
Step 1: Unpack the Smart Media Converter.
Step 2: Connect the 5V DC power adapter to the XST-705A and verify that
the Power LED lights up.
(Please refer to the 4.4 Power Information section for power input.)
Step 3: 3-1: Prepare a twisted-pair, straight-through Category 5e/6/7 UTP cable for Ethernet connection. 3-2: Prepare a fiber cable for connection to the 10GBASE-T SFP+ slot, and make sure both sides of the SFP transceiver are with the same media type. (Please refer to the 3.5 Cable Connection section for the type of connection.)
Step 4: 4-1: Insert one side of Category 5e/6/7 cable into the Smart Media Converter Ethernet port (RJ45) while the other side of Category 5e/6/7 cable into the network devices’ Ethernet port (RJ45), e.g., switch, PC or server. The UTP port (RJ45) LED on the Smart Media Converter will light up when the cable is connected with the network device. (Please refer to the 4.2 LED Indicators section for the functions of LED lights.)
Connect the fiber cable. Attach the duplex LC connector on the network cable to the SFP+ transceiver. Attach the fiber cable from the XST-705A to the fiber network. TX, RX must be paired at both ends.
Step 5: When all the connections are all set and all the LED lights show normal, the installation is complete.
Wall-mount Installation
Step 1: Please find the wall that can mount the Smart Media Converter
Step 2: Screw two screws on the wall.
Step 3: Hang the Smart Media Converter on the screws from the wall.
Step 4: Refer to Chapter 4.4 Power Information on power supply to the
Smart Media Converter.
Before mounting the device to the wall, please check the location of the electrical outlet and the length of theEthernet cable.
Slide Media Converter Module into MC-1610MR/MC-1610MR48
Chassisinstallation
To install the Smart Media Converter in a 19-inch standard rack, follow the
instructions described below.
Step 1: Unscrew and pull out the Smart Media Converter board.
Step 2: Remove a blank faceplate from an empty expansion slot on the front of the chassis. The Smart Media Converter board can be installed in any expansion slot.
Step 3: Slide the Smart Media Converter board into the expansion slot, aligning it with the guide rails, until it firmly connects to the chassis’ backplane.
Step 4: Secure the Smart Media Converter board to the chassis by tightening the thumbscrew.
- Never push the converter into the slot with force; it could damage the chassis.
- The Smart Media Converter Chassis supports hot-swap; there is no need to turn off the whole chassis before sliding in the new converter.
Cable Connection
- Installing the SFP+ Transceiver
- The sections describe how to insert an SFP+ transceiver into an SFP+ slot.
- The SFP+ transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP+ port without having topower down the Smart Media Converter.
- It is recommended to use PLANET SFP+s on the Smart Media Converter. If you insert an SFP+ transceiver that is not supported, the Smart Media Converter will not recognize it.
10GBASE-X SR/LR:
Before connecting the other switches, workstation or Smart Media Converter,
please do the following:
- Make sure both sides of the SFP+ transceiver are with the same media type; for example, 10GBASE-SR to 10GBASE-SR, 10GBASE-LR to 10GBASE-LR.
- Check whether the fiber-optic cable type matches the SFP+ transceiver model.
- To connect to 10GBASE-SR SFP+ transceiver, use the multi-mode fiber cable with one side being the male duplex LC connector type.
- To connect to 10GBASE-LR SFP+ transceiver, use the single-mode fiber cable with one side being the male duplex LC connector type.
Connecting the fiber cable
- Attach the duplex LC connector of the network cable to the SFP+ transceiver.
- Connect the other end of the cable to a device like a switch with SFP+ installed, fiber NIC on a workstation or a Smart Media Converter.
- Removing the Transceiver Module
- Make sure there is no network activity by consulting or checking with the network administrator. Or through the management interface of the switch/converter (if available), disable the port in advance.
- Remove the fiber optic cable gently.
- Turn the lever of the MTB module to a horizontal position.
- Pull out the module gently through the lever.
Note
Never pull out the module without pulling the lever or the push bolts on the
module. Directly pulling out the module with effort could damage the module
and SFP+ module slot of the Smart Media Converter
10G/5G/2.5G/1G/100BASE-T
The 10G/5G/2.5G/1G/100BASE-T port comes with auto-negotiation capability. It
automatically supports 100BASE-TX, 1GBASE-T, 2.5GBASE-T, 5GBASE-T and
10GBASE-T networks. Users only need toplug a working network device into the
10G/5G/2.5G/1G/100BASE-T port, and then turn on the Smart Media Converter.
The port willautomatically run at 100Mbps, 1000Mbps, 2500Mbps or 5000Mbps and
10000Mbps after the negotiation with the connected device.
Connecting the UTP Cable
The 10G/5G/2.5G/1G/100BASE-T port uses RJ45 socket — similar to phone jack —
for connection of unshielded twisted-pair cable (UTP). The
802.3u/802.3ab/802.3bz/802.3ae Ethernet standard requires Category 5 UTP for
100Mbps 100BASE-TX. 10G/5G/2.5G/1G/100BASE-T uses Cat5e/6/6A/7 UTP (see table
below). Maximum distance is 100 meters (328 feet).
| Standard | Transfer Speed | Cable Requirement (100M) |
|---|---|---|
| 10GBASE-T | 10000Mbit/s | Cat 6A/7 |
| 5GBASE-T | 5000Mbit/s | Cat 6/6A/7 |
| 2.5GBASE-T | 2500Mbit/s | Cat 5e/6/6A/7 |
| 1000BASET | 1000Mbit/s | Cat 5e/6/6A/7 |
| 100BASE-TX | 100Mbit/s | Cat 5/5e/6/6A/7 |
Note
Be sure the connected network devices support MDI/ MDI-X. If it does not
support, then use the crossover Category 5e6/6A/7 cable.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy
saving, please remove the power cable to disconnect the device from the power
circuit. Without removing powercable, the device will still consume power from
the power source. In view of Saving the Energy and reducing the unnecessary
power consumption, it is strongly suggested to remove the powerconnection for
the device if this device is not intended to be active.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>