BEGA 50 249.6 Recessed Ceiling Downlight for Indoor Use Instruction Manual

BEGA 50 249.6 Recessed Ceiling Downlight for Indoor Use

Product Information

This product is a luminaire designed for connecting to an external LED power supply unit. It has an aluminium housing shield with a velvet black finish on the outside and a matt copper hue on the inside. The luminaire features a light-diffusing silicone lens and a reflector made of high-gloss anodised pure aluminium. It is equipped with adjustable claws for fixing and comes with a connecting cable with strain relief and plug.

Safety

The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should perform the installation and commissioning. The manufacturer does not accept liability for damage caused by improper use or installation. Any modifications made to the luminaire will make the person responsible for these modifications considered as the manufacturer.

Overvoltage Protection

The electronic components in this luminaire are protected against overvoltage according to DIN EN 61547. To achieve additional protection against transients and other factors, separate overvoltage protection components are recommended. These components can be found on the manufacturer’s website at www.bega.com.

Technical Specifications

• Lamp Module connected wattage: 6W
• Luminaire connected wattage: 8W
• Colour temperature: 3000K
• Colour rendering index: >90
• Module luminous flux: 880lm
• Luminaire luminous flux: 462lm
• Luminaire luminous efficiency: 57.8lm/W

Product Usage Instructions

To install the luminaire, follow these steps:

1. Ensure you are familiar with and comply with national safety regulations.
2. Only a qualified electrician should perform the installation and commissioning.
3. Connect the luminaire to an external LED power supply unit using the provided connecting cable with strain relief and plug.
4. Avoid touching the high-quality components, such as the silicone lens and reflector, with your fingers during installation or replacement.
5. For replacing the LED module, refer to the label inside the luminaire for the module designation. Use BEGA replacement modules that comply with the manufacturer’s specifications.
6. To replace the LED module, remove the fixing claws and detach the connection frame of the luminaire. Follow the instructions provided in the installation manual to properly install the replacement module.

DIMENSIONS

Instructions for use

Application

• Recessed ceiling luminaire · indoor luminaire with aluminium housing for shielded light deflected downwards.
• Luminaire for connection to external LED power supply unit.

Product Description

• Recessed LED ceiling luminaire »STUDIO LINE« made of die-cast aluminium – without power supply unit
• Aluminium housing shield,
• Finish Colour velvet black inside hue matt copper
• Light-diffusing silicone lens
• Reflector of anodised pure aluminium
• Fixing is achieved by using 2 adjustable wedge-shaped claws 1 connecting cable with strain relief and plug connector system for BEGA power supply unit, on/off or DALI
• Safety class III
•  – Conformity mark
• Weight: 0.2 kg
• This product contains light sources of energy efficiency class(es) E

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at  www.bega.com.

Lamp

• Module connected wattage 6 W
• Luminaire connected wattage 8 W
• Rated temperature ta = 25 °C
• Ambient temperature ta max = 35 °C
• When installed in heat-insulating material ta max = 25 °C

50 249.6 K3

• Module designation LED-0500/930
• Colour temperature 3000 K
• Colour rendering index CRI > 90
• Module luminous flux 880 lm
• Luminaire luminous flux 462 lm
• Luminaire luminous efficiency 57,8 lm / W

Lighting technology

• Half beam angle 48°

Installation

A separate power supply unit is required to operate the luminaire – see accessories.

• The recessed opening will be covered by the frame of the luminaire.
• Fixing of the luminaire is achieved by using 2 adjustable wedge-shaped claws.
• LEDs are high-quality electronic components!
• Please avoid touching them directly during installation or relamping.

Installation into false ceilings

• A recessed opening of ø 68 mm is necessary to accept the luminaire.
• Free space depth min. 55 mm (see sketch).
• Luminaire and external LED-power supply unit must not be installed in heatinsulating material.
• The lateral distance between recessed luminaire and standard combustible building parts must be at least 50 mm.
• The claws catch the panel from the reverse side. If minimum thickness of the panel is less than 3 mm it must be reinforced from the reverse side. Maximum thickness of the panel must be no more than 20 mm.
• For connection to external LED-power supply unit – accessory 13 198 or 13 199 – the luminaire is equipped with a 2-pin connector.
• Note operating instructions of the LED-power supply units.
• Push external LED power supply unit and luminaire into the ceiling cut-out.
• Hand-tight screws of claw fasteners evenly.
• Center reflector onto the enclosed housing shield.
• Mount housing shield with reflector onto luminaire frame (magnetic) (see sketch).

Cleaning · Maintenance

• Clean luminaire regularly with solvent-free cleansers from dirt.

Replacement of the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
• Disconnect the system.
• Pull housing shield with mounted reflector from luminaire frame.
• Please follow the installation instructions for the LED module.
• Mount housing shield with reflector onto luminaire frame (magnetic).

Accessories

• Power supply units for LED luminaires 220-240 V · 0/50-60 Hz with strain relief and plug connector system.
• 13 198 Power supply unit on/off
• 13 199 Power supply unit DALI
• The power supply units are only suitable for the operation of one LED luminaire.
• For the accessories a separate instructions for use can be provided upon request.

Spares

• Shield 42 000 202 .3M 8
• LED module 3000 K LED-0500/930
• Reflector 76 001 317

BEGA Gantenbrink-Leuchten KG

• Postfach 31 60 · 58689 Menden
• info@bega.com
• www.bega.com

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>