VEVOR P8038 Heat Press Machine Instruction Manual

HEAT PRESS
P8038

Start Here
Warnings must be followed carefully to avoid body injury.

Transfer Parameter (for reference)

Main parameters

1. How to turn on/off and how to start?
   Press the switch button on the side of the thermostat to start the machine.
   Press once to count down and press again to reset.

2. How to set the temperature/time?
   Press once to set the temperature, press twice to set the time and press again to exit. (It will automatically exit the temperature/time setup state in case of no operation within 5sec.).

3. How to set the temperature/time to increase or decrease?
   Set the time/temperature increase
   Set the time/temperature decrease

4. How to change the temperature unit from °C to °F?
   In the power-on state, press “+” and “-” at the same time to change the temperature unit between °C and °F.

5. How to set auto shutdown time?
   Press and hold for 5 sec. to set the auto shutdown time.
   (The factory default is 60min and the range is from 10min to 120min)

6. How to do temperature correction?
   Press and hold for 5 seconds to enter the temperature correction setting. (Range +30°C, initial value is 0)

7. How to turn on / off the beep sound?
   In the shutdown state, press “-” to turn off the sound and OFF is shown; Press again to turn on the sound and ON is shown.

8. Tips: The max. set temperature of this machine is 210°C and the longest time is 999sec.

Plate transfer process

1. Select one side that matches the size of the plate to be sleeved with a silica gel pad, and remove the silica gel pad on the other side;
   Keep the side without silica gel pad facing upwards and heat it on the machine for 15 minutes,

2. Put the hot stamping paper on the plate that wants to print the pattern.

3. Remove the heating plate and place it on the plate, keeping the side without silica gel pad facing upward

This mug heat press machine is matched with 5 in 1 and 6 in 1.

180℃（360℉）180S

1. Connect the cap baking machine to the main machine and set the time and temperature
2. Stick the transferred picture on the hat
3. When the temperature reaches, place the hat into the hat baking machine and press tightly

This mug heat press machine is matched with 8 in 1,10 in 1,11 in 1

180℃（360℉）180S

1. Connect the cap baking machine to the main machine and set the time and temperature
2. Stick the transferred picture on the hat.
3. When the temperature reaches, place the hat into the hat baking machine and press tightly.

Main spare parts

1. Pedestal
2. Placement
3. Heating plate
4. Handle
5. Aviation connector
6. Button
7. Lift knob
8. Overload protector
9. Power socket
10. Power switch
11. Column

Guarantee

The products are strictly based on the Consumer Protection Law of the People’s Republic
of China and the Product Quality Law of the People’s Republic of China. The services are as follows.
Within 12 months, this product has the performance failure listed in the Product Performance Failure Table” It is confirmed by SUNMETA and can be used for maintenance service free of charge. If out of validity, damage caused by force majeure, or human  causes, the machine is not covered by the warranty, repair in charge.

Safety instruction:setore operating this unit, please read these instructions completely and save them
Notice
Keep unplug when moving the machine
Keep unplug when installing accessories
Place on a flat and stable platform and operate under ventilated conditions
Wear special protective equipment when operating the machine

Warning tmproper use may result in electric shock, fire, personal injury and other damage ponotuse this machine in a hazardous location ponotuse when the machine is not working properly
Do not allow children or adults who do not understand this manual to operate this machine
Do not disassemble and repair this machine
Do not use an unsuitable AC outlet.
Do not touch the heating plate when the machine heating

Warranty content

Product Performance Failure Table

Machine body| Parts of the machine itself (excluding main parts)| One year| Fault 1| The machine cannot be used normally according to the operating procedure
---|---|---|---|---
Main parts| 38*38mm aluminum alloy heating plate| One year| Fault 2| Heating plate not heating
PCBA(circuit board)| One year| Fault 3| Display error
Mug heating element| 90days| Fault 4| Failure heating
Pen heating element, cap heating element| One year| Fault 5| Failure heating

Circuit Board Wiring Method

1. Cables on the motherboard and display
2. NTC temperature probe
3. Hot plate
4. Main incoming line
5. Heating plate zero line
6. Main incoming zero line

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>