ZEBRONICS ZEB-JUKE BAR 3810 Dolby Soundbar User Manual

ZEBRONICS ZEB-JUKE BAR 3810 Dolby Soundbar User Manual

www.zebronics.com

Important Safety Instruction

Thank you for purchasing the ZEB-JUKE BAR 3810 PRO DOLBY Soundbar. Please read this user manual carefully and keep for future reference.

Warning

Caution:

• To reduce the risk of electric shock, do not dismantle the product and do not expose the apparatus to rain or moisture. No user serviceable parts inside.
• Refer servicing to qualified personnel only.

The lightning flash within an equilateral triangle is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock to a person or persons.

⚠ Important! This symbol alerts you to read and observe important warnings and instructions on the unit or in this manual.

Notice:
This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

1. To prevent possible hearing damage, do not listen at high volume levels for long-time periods or a sudden high volume level.
2. Never use the device unsupervised! Switch off the device whenever you are not using it, even if not using it only for a short while.
3. The appliance is not intended to be operated by means of an external timer or separate remote control system.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
5. Before operating this system, check the voltage of this system to see if it is identical to the voltage of your local power supply.
6. The unit should not be impeded by covering the ventilation opening with items such as newspaper, table-cloths, curtains etc. Make sure that there are at least 20 cm of space above and at least 5 cm of space on each side of the unit.
7. The apparatus must not be exposed to dripping or splashing liquid, no objects filled with liquids such as vases, should be placed on the apparatus.
8. To prevent fire or shock hazard, do not expose this equipment to direct heat, rain, moisture or dust.
9. Do not position this unit near any water sources e.g. taps, bathtubs, washing machines or swimming pools. Ensure that you place the unit on a dry, stable surface.
10. Do not place this unit close to a strong magnetic field.
11. Do not place the unit on a amplifier or receiver.
12. Do not place this unit in a damp area as the moisture will affect the life of electric components.
13. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Wipe with a clean, dry or slightly damp cloth.
14. When removing the power plug from the wall outlet, always pull directly on the plug, never pull on the cord.
15. Depending on the electromagnetic waves used by a television broadcast, if a TV is turned on near this unit while it is also on, lines might appear on the LED TY. Neither this unit nor the TV is malfunctioning. If you see such lines, keep this unit well away from the TV set.
16. The mains plug is used to disconnect the device, the disconnected device should remain readily operable.

Important Safety Instructions

1. Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.

2. Do not use this apparatus near water.

3. Clean only with dry cloth.

4. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

5. Do not install near any heat sources such as radiators, heaters, stoves, or other apparatus (including amplifiers) that produce heat.

6. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles or at the point where they exit from the apparatus.

7. Only use attachments/accessories specified by the manufacturer.

8. Unplug this apparatus during lightning storms or when unused for long periods of time.

9. Refer all servicing to qualified service personal. Servicing is required when the apparatus has been damage in any way, for example, when the power-supply cord or plug
   is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

10. The AC plug is used to disconnect the device, the disconnected device should remain readily operable. In order to disconnect the apparatus from the AC power completely, the AC plug must be removed from the AC outlet completely.

Power Source

This Sound bar is designed to operate in 220V -240V- 50Hz/60Hz

Important Notes

• This sound bar was especially developed for LED/LCD/Plasma TV’s: It should not be used in combination with CRT TV’s (Cathode Ray Tube TV’s) in order to avoid image interference.
• Safety and operating instruction manual should be retained for future reference.
• The apparatus should not be exposed to dripping, splashing or placed in a humid atmosphere such as a bathroom.
• Do not install the product in the following areas:
  • Places exposed to direct sunlight or close to radiators.
  • On top of other stereo equipment that radiate too much heat-Blocking ventilation or in a dusty area.
  • Areas where there is constant vibration.
  • Humid or moist places.
  • Do not place near candles or other flames.
• Operate the product only as instructed in this manual.
• Before turning on the power for the first time, make sure the sound bar is plugged to power outlet.
• For safety reasons, do not remove any covers or attempt to gain access to the inside of the product. Refer any servicing to qualified personnel.
• Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable parts inside. Refer all servicing to qualified service personnel.

Product Representation

Sound Bar

1. DISPLAY
2. VOL+/-
3. Power/INPUT
4. USB
5. AUX
6. OPTICAL IN
7. HDMl(ARC)
8. ACIN

Remote Control

1.  : Standby mode for power on/off.

2.  PAIR: Connect or disconnect to the pairing device.
   (Press the button more than 2 seconds).

3. VOL+ : Master volume up.

4. ◀◀: Previous Track (Only work under USB & BT Mode).

5. VOL- : Master volume down.

6. MUSIC: Select the Music EQ effect.

7. TREB+ : Treble volume up.

8. TREB- : Treble volume down.

9. MUTE : Mute Mode.

10. INPUT : Input mode (AUX/USB/HDMl(ARC)/OPT/BT)

11.  ▶▶ | : Next Track (Only work under USB & BT mode).

12. ▶▶ Ⅱ / RESET
    Play/Pause : Play/ Pause for Current Track (Only work under USB and BT mode).
    Reset : Press and hold the button more than 2 sec. to Set all functions to manufacturer defaults.

13. MOVIE: Select the Movie EQ effect.

14. NEWS: Select the News EQ effect.

15. BASS+ : To increase the bass. (Refer to Bass chapter for reference.)

16. BASS- : To decrease the bass. (Refer to Bass chapter for reference.)

17. 3D: Select the 3D EQ effect.

Positioning the Sound Bar

Place on a flat Surface
Place the sound bar horizontally on a flat surface such as a TV unit or shelves and align it centrally with the TV screen. Allow some space between the speaker and the wall. Don’t place inside a cabinet or an a walled shelf. Follow this guidance for best sound output and good airflow around the sound bar.

Mount on the wall
WARNING : If you don’t feel confident to correctly and securely wall- mount the sound bar, Seek the assistance of an experienced person of professional.

Install the speaker on a vertical, fast, reinforced area of wall. For plaster walls, it is recommended to screw into wall studs for greater security. For optimum performance, allow at least 25mm/1″distance between the sound bar and the TV.

Follow below steps to mount the sound bar on the wall

1. Make 2 holes on the wall with distance same as the wall bracket on the soundbar
2. Put the plastic anchors onto the wall and secure the screws to the plastic clip, do not tighten the screws all the way make sure leave some space
3. Attached the 2 EVA pads onto the wall mount bracket. This will make sure that there is enough room between the wall and the sound bar outlet, minimum 15mm
4. Once the screws securely fastened, hang the sound bar over by inserting the screws onto the wall mount bracket

OPERATE INSTRUCTIONS

Setting the Sound bar

1. Plug in the power cord and the display will light up (Standby mode).
2. Switch on the soundbar by using power button on soundbar or by using STANDBY button on remote. After switching on, the default input mode will appear on display.
3. Input mode can be changed by pressing the INPUT button on remote or on sound bar.
4. Below are input mode names appearing in the soundbar display:

BT : BT Pairing mode
RUX :AUX Mode | HD : HDMl(ARC)Mode
OPTI : Optical mode | USB : USB Mode

Powering On/Off

1. Plug the sound bar into a wall outlet, it will automatically enter standby mode.
2. Short-press the power button to turn on the sound bar.
3. To turn off, press the power button on remote control or on sound bar or unplug from wall outlet.

Playing Audio via BT Connection

1. Turn the sound bar on, press the STANDBY button on the sound bar or the POWER button on the remote control to select the BT mode. When BT is selected, 11 BT II will be displayed on the LED display and the blue LED on the sound bar will flicker followed by a double beep sound to indicate BT pairing mode is now active.
2. Turn the BT of your device on, search for 11 ZEB-JUKE BAR 3810 PRO DOLBY II on your BT list, and then select BT connection.
3. When successfully paired, you will hear a tone and the ” BT “on the screen stops flickering. Then the music on your phone or other compatible device that you selected can be played on the sound bar.
4. Use the volume knob on the soundbar or on the remote controller to adjust the volume.
5. The remote controller includes BT mode playback controls. Press and hold PAIR button on the remote controller for more than 2 seconds to disconnect the paired BT device or to reconnect with the previously connected BT device.
6. If you wish, you can change the audio settings by using the relevant buttons on the remote controller.

Playing Audio via use Port

The sound bar automatically switches to USB input mode with the LED display ” USB ” when a USB flash drive is inserted

When a USB flash drive is inserted and soundbar is powered on, press the INPUT key on remote controller or STANDBY button on sound bar to switch to USB input mode (in case it doesn’t change automatically) with LED display lighting up” USB “. And music in the USB will be automatically played.

This mode isn’t selectable on the sound bar or remote control unless a USB flash drive is connected).

1. Ensure that your USB flash drive contains MP3 audio files (other file types not supported).
2. Connect the USB flash drive to the USB port on the sound bar (or your own USB extension cable connected to the USB port); music will automatically play.
3. The remote control includes USB input mode playback controls.

Audio Input (AUX) Connection

1. Firstly connect the soundbar to your PC, laptop, smart-phone, TV, or other audio devices by using an AUX cable provided. Make sure that these devices have both AUX IN and AUX OUT terminals.
2. Then press the STANDBY button or INPUT button on remote control to switch the soundbar to Aux mode, once the soundbar is connected in Aux mode, the screen will display “RUX” . And the music on your connected device will play. Playback can only be controlled on your connected device.

Note: For some computers, you may need to access the audio control panel to manually set the sound bar as below picture.

HDMI (ARC) Mode

1. The soundbar supports HDMI (ARC) with audio return channel (ARC). You can hear the TV audio through your soundbar by using a single HDMI (ARC) cable. But on condition that your TV is ARC compliant.
2. Using a high speed HDMI (ARC) cable, connect the HDMI (ARC) connector on the sound bar to the HDMI (ARC) connector on the TV. The HDMI (ARC) connector on the TV might be labeled differently. For details, see the user manual of your TV.
3. When HDMI (ARC) is connected, TV sound setting in “sound output” mode should be set as , in addition, digital audio output mode should be set as or . When the HDMI (ARC) cable is connected, the TV digital audio output is set as Dolby or Auto mode. Then start playing music on the TV.
4. Press “INPUT” button on the remote control or “STANDBY” button on soundbar to select HD -H DM I (ARC) mode. Different TV might be different setting, please refer to your TV User Manual.
5. Use the volume buttons to adjust the volume to your requirements.
6. You can also change the audio settings by using the relevant buttons on the remote control.

Note:

1. When connecting a device such as a TV/Set-top box/DVD/ game console with HOM/ (ARC) cable, set the audio output mode of the device to Dolby or Auto mode <digital HOM/ (ARC) output>.
2. The TV is connected to a HOM/ (ARC) port with sound bar. Different TVs might have different setup menus, but the operation approach is the same.
3. If needs to connect set-up box meanwhile, please firstly connect the HOM/ (ARC) connector and paired to the sound bar. Then connect the set-top box.

Optical Mode
Remove the cap of optical cable (keep the cap for the future use); check the direction of the plug. Connect the soundbar and TV with the optical cable.

Use this mode to play music from a TV with optical digital output on the sound bar. In TV sound settings, select the soundbar optical connection (output for audio). When the optical cable is connected, the TV audio output is set to Dolby or Auto mode.

The TV must have an optical digital output. Use the optical cable to make the connection as follows:

1. Connect the optical cable to the optical digital output of your TV.
2. Connect the optical cable to the optical digital input of your sound bar.
3. Switch on the TV set and the sound bar. Set the connected TV to “Dolby or Auto mode”.
4. Start playing on the TV.
5. Press “INPUT” button on the remote control or “STANDBY” button on the soundbar to select OPTI- OPTICAL mode.
6. Use the volume buttons to adjust the volume to your requirements.
7. You can also change the audio settings by using the relevant buttons on the remote control.

Note:

1. When connecting a device such as a TV/Set-top box/ DVD/ game console with optical cable, set the audio output mode of the device to Dolby or Auto mode (digital optical output).
2. Do not bend the optical cable, otherwise the cable inside  will be damaged.

Features:

Wireless BT/USS/AUX/Optical IN/HDMI (ARC)
Dolby Audio
Remote control
Wall Mountable
LED Display
Volume/Media Control
Glossy Finish
Powerful Quad Drivers
Retro Style Volume Controller

Specifications

Package Content

Sound Bar : 1 U
Remote Control : 1 U
Input cable : 1 U
QR Code Guide : 1 U
Wall mount bracket with fasteners : 1 U

Troubleshooting

ISO 9001:2015 Certified Company
www.zebronics.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>