BEGA 51219.4K3 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 51219.4K3 Wall Luminaire
Product Information
Product Usage Instructions
OVERVIEW
Instructions for use
Product Description
Overvoltage protection
Installation
Cleaning · Maintenance
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 51219.4K3 Wall Luminaire

Product Information

Safety| The installation and operation of this luminaire are subject to
national safety regulations. Installation and commissioning may
only be carried out by a qualified electrician. The manufacturer
accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the
luminaire, the person responsible for these modifications shall be
considered the manufacturer.
---|---
Overvoltage Protection| The electronic components installed in the luminaire are
protected against overvoltage in accordance with DIN EN 61547. To
achieve additional protection against e.g. transients, etc. we
recommend separate overvoltage protection components. You can find
them on our website at www.bega.com.
The lamp Module connected wattage| 25 W
Luminaire connected wattage| 28.4 W
Rated temperature| Ambient temperature: 25 – 30°C
Module designation| LED-1166/930
Color temperature| 3000 K
Color rendering index| CRI > 90
Module luminous flux| 3900 lm
Luminaire luminous flux| 712 lm
Luminaire luminous efficiency| 25.1 lm / W

Product Usage Instructions

To ensure the safe installation and usage of the luminaire, please follow the instructions below:

Installation and commissioning should only be carried out by a qualified electrician.
Follow the national safety regulations for the installation and operation of the luminaire.
Do not modify the luminaire without proper authorization from the manufacturer.
If additional protection against overvoltage or transients is required, consider using separate overvoltage protection components available on our website.
The lamp module connected wattage is 25 W.
The luminaire-connected wattage is 28.4 W.
The rated temperature for the luminaire is between 25°C and 30°C.
The module designation is LED-1166/930.
The color temperature is 3000 K.
The color rendering index (CRI) is greater than 90.
The module luminous flux is 3900 lm.
The luminaire luminous flux is 712 lm.
The luminaire luminous efficiency is 25.1 lm / W.

OVERVIEW

$BEGA-51219-4K3-Wall-Luminaire-FIG-1 $1$$

Instructions for use

Application

Wall luminaire · Indoor luminaire with velvet black metal housing.
Luminaire with light source shielded to the front and metallic inside color of the reflection surface.
Radial light emission 360°.

Product Description

Wall luminaire “STUDIO LINE”
Luminaire housing made of aluminum, surface Colour velvet black inside hue matt brass
Inside the synthetic cover, translucent white
3 fixing holes ø 4.5 mm
Angle 120° · Pitch circle ø 155 mm 1 cable entry for through-wiring for mains cable
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 170-280 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
- c – Conformity mark
Weight: 3.1 kg

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected wattage 25 W
Luminaire connected wattage 28.4 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 30 °C

51 219.4 K3

Module designation LED-1166/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 3900 lm
Luminaire luminous flux 712 lm
Luminaire luminous efficiency 25,1 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Remove the mounting plate with LED unit from its packaging.
Please note: A round blank made of synthetic material covers the mains connection compartment. For the mains supply connection, this synthetic round blank must be removed and refitted after the mains supply connection. Loosen the black knurled screw (slotted) and remove the round made of synthetic material from the LED unit. Pass the power connecting cable through the cable entry in the mounting plate. $BEGA-51219-4K3-Wall-Luminaire-FIG-1 $2$$

Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface. Establish the earth conductor connection on the earthing screw (1) of the mounting plate.Make the electrical connection to the terminals. Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N). Insert the round made of synthetic material back into the LED unit and tighten the black knurled screw (slotted). Remove the luminaire housing (reflector) from its packaging and carefully guide over the LED unit. Place the luminaire housing (reflector) over the keyholes onto two threaded bolts of the LED unit and turn it clockwise until it stops. Tighten the two hex nuts M4 over the keyholes. Remove the supplied radial synthetic cover with round housing cover from the packaging, guide onto the centre of the grub screw of the LED unit and hand-tighten in the clockwise direction.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module ·
Replacing the power supply unit The designation of the LED module is noted ona label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools. Disconnect the system from the power supply. Loosen the radial synthetic cover with round housing cover by turning it anti-clockwise from the LED unit. Loosen the black knurled screw (slotted) and remove the round made of synthetic material from the LED unit. Disconnect the earth conductor connection and the electrical connection to the terminal. Loosen the mounting screws of the power supply unit, the round blank bracket and earthing screws (Torx). Remove the pot with LED module. Install the replacement pot. Please follow the installation instructions for the LED module. Replace defective LED power supply unit. Tighten the mounting screws of the power supply unit, the round blank bracket and earthing screws (Torx) again. Establish the earth conductor connection on the earthing screw (1) of the mounting plate. Make the electrical connection to the terminals. Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N). Insert the round made of synthetic material back into the LED unit and tighten the black knurled screw (slotted). Guide the radial synthetic cover with round housing cover onto the centre of the grub screw of the LED unit and hand-tighten in the clockwise direction.

Spares